CB017E0222JBA

Manufacturer Part NumberCB017E0222JBA
DescriptionFilm Chip Cap 2,2 nF 100 V 5 %
ManufacturerAVX Corporation
CB017E0222JBA datasheet
 


Specifications of CB017E0222JBA

Lead_time154Pack_quantity3900
1
2
3
4
5
6
7
8
9
10
11
Page 11
12
Page 12
13
Page 13
14
Page 14
15
Page 15
16
Page 16
17
Page 17
18
Page 18
19
Page 19
Page 15/19

Download datasheet (207Kb)Embed
PrevNext
Film Chip Capacitors
PEN DIELECTRIC – CB Series
MOUNTING AND SOLDERING RECOMMENDATIONS
SOLDERING PROFILE
The capacitors can be mounted using infrared and vapor phase soldering following recommended below. They are NOT
suitable for wave soldering.
Phase
Size
Preheating
All
1206 to 1812
Soldering
2220 to 6054
*Reflow soldering referring to JEDEC Standard with some limitations
*JEDEC J-Std 020C
RECOMMENDED SOLDER PASTE THICKNESS
For optimum solderability, the recommended soldering
paste thickness: 1206 to 2824 :150 to 200μm
C
B
A
RECOMMENDED CLEANING
To clean flux from the PC board assembly, the recommended
products are: ethanol, isopropyl alcohol, and deionized water
wash. The cleaning products to avoid are: Toluene, Xylene,
Trichloroethylene, Terpene Cleaner EC-7, surface active
agent. In case of using another solvent, please contact us.
TIN WHISKERS TESTS : JEDEC STANDARD NO 22A121
Stress Type
Ref. Spec.
Temperature cycling
JESD22-A104
Ambient Temperature /
Humidity Storage
High Temperature /
Humidity Storage
34
Temperature (°C)*
160 to 180°C max
T max= 250°C and 10 s between T max and Tmax-5°C
T max= 255°C and 10 s between T max and Tmax-5°C
In case of hand soldering, the temperature of the soldering
iron should not be above 250°C. Special care must be taken
to avoid touching the capacitor body with the iron tip.
PAD DIMENSIONS:
millimeters (inches)
Size Code
Case Size
01
1206
1.30 (0.051)
02
1210
2.00 (0.079)
03
1812
3.00 (0.118)
04
2220
5.00 (0.195)
05
2824
6.00 (0.234)
16
4030
7.50 (0.295)
17
5040
11.2 (0.441)
18
6054
14.6 (0.575)
OTHER CAUTIONS
Flame retardancy: the dielectric film is not a flame retardant
material.
Environment: contact us when chips are used in humid or
gas atmosphere and /or when using resin.
Recommended handling: do not use edged tools, so not
to damage the capacitors.
Test Conditions
-55°C +85(+10/-0)°C air 5
to 10mn soak 3 cycles/hour
30+/-2°C - 60+/-3% RH -2000H
70+/-5°C - 93+3/-2% RH -1000H
Time (s)
180s max.
60s at temperature> 217°C
75s at temperature > 217°C
A
B
C
1.30 (0.051)
2.20 (0.087)
1.30 (0.051)
2.20 (0.087)
1.50 (0.059)
3.50 (0.137)
1.90 (0.075)
4.50 (0.178)
2.50 (0.098)
5.70 (0.224)
3.00 (0.118)
8.00 (0.315)
3.50 (0.137)
10.3 (0.406)
3.60 (0.147)
12.6 (0.496)
Analysis
Results
SEM x 1000
Pass
SEM x 1000
Pass
SEM x 1000
Pass