MAX465 MAXIM [Maxim Integrated Products], MAX465 Datasheet
MAX465
Available stocks
Related parts for MAX465
MAX465 Summary of contents
Page 1
... Narrow Plastic DIP 0°C to +70°C 24 Wide SO 0°C to +70°C Dice* -40°C to +85°C 24 Narrow Plastic DIP -40°C to +85°C 24 Wide SO = +25°C, DC parameters only GND MAX463 MAX465 OUT0 ...
Page 2
... LOAD f = 10MHz IN MAX463/MAX464, MAX467/MAX468 MAX465/MAX466, MAX469/MAX470 MAX463/MAX464 150 MAX465/MAX466 0.7 MAX463–MAX466 MAX463/MAX465/MAX467/MAX469 MAX464/MAX466/MAX468/MAX470 MAX463/MAX465, disabled mode MAX464/MAX466, disabled mode = +25° MIN MAX UNITS TYP MAX MIN MAX ±5.25 ±4.75 ±5. ±3 ±10 ± ...
Page 3
... Logic Input Current Low I INLO _______________________________________________________________________________________ Two-Channel, Triple/Quad = 75Ω, unless otherwise noted.) T CONDITIONS MIN MAX463/MAX465/MAX467/MAX469 MAX464/MAX466/MAX468/MAX470 MAX463/MAX465, disabled mode MAX464/MAX466, disabled mode f = 10kHz IN MAX463/MAX464, MAX467/MAX468 MAX465/MAX466, MAX469/MAX470 MAX463/MAX464, MAX467/MAX468 MAX465/MAX466, MAX469/MAX470 MAX463/MAX464, MAX467/MAX468 MAX465/MAX466, MAX469/MAX470 MAX463/MAX464, MAX467/MAX468 MAX465/MAX466, MAX469/MAX470 V = 2V-to-0V step IN f ...
Page 4
Two-Channel, Triple/Quad RGB Video Switches and Buffers ELECTRICAL CHARACTERISTICS (continued) ( -5V, -2V ≤ V ≤ +2V LOAD PARAMETER SYMBOL Address Setup Time (Note 11 Address Hold Time (Note 11 ...
Page 5
... I– –50 – 100 TEMPERATURE (°C) MAX465 DISABLED OUTPUT RESISTANCE vs. TEMPERATURE 1.30 1.25 1.20 1.15 1.10 –50 – 100 TEMPERATURE (°C) OUTPUT VOLTAGE SWING vs. LOAD RESISTANCE MAX463/4/7/8 MAX465/6/9/70 –1 –2 –3 –4 10 100 1000 10000 LOAD RESISTANCE ( ) 5 ...
Page 6
Two-Channel, Triple/Quad RGB Video Switches and Buffers ____________________________Typical Operating Characteristics (continued +25°C, unless otherwise noted.) A MAX464 SMALL-SIGNAL STEP RESPONSE GND GND 10ns/div MAX464 LARGE-SIGNAL STEP RESPONSE GND GND 20ns/div MAX464 OUTPUT TRANSIENT WHEN SWITCHING BETWEEN TWO GROUNDED ...
Page 7
... RGB Video Switches and Buffers _____________________________________________________________Pin Descriptions PIN MAX463/MAX465 MAX464/MAX466 11, 15, 24 11, 13 – 21 – 14 – 14 PIN MAX467/MAX469 MAX468/MAX470 ...
Page 8
... RC product becomes too large. The MAX465/MAX466/MAX469/MAX470’s amplifiers are internally configured for a gain of two, resulting in an over- all gain of one at the cable output when driving back-ter- minated coaxial cable (see the section Driving Coaxial Cable ) ...
Page 9
... The MAX465/MAX466/MAX469/MAX470 will drive a 150Ω load (75Ω back-terminated cable) to ±2.5V. The Typical Operating Circuit shows the MAX465/MAX466 driving four back-terminated 75Ω video cables. The back-termination resistor (at each amplifier output) pro- vides impedance matching at the driven end of the cable to eliminate signal reflections ...
Page 10
... Figure 3c. Step Response with an Isolation Resistor disabled MAX463/MAX464 outputs exhibit a 250kΩ typical resistance. Because their internal feedback resistors are required to produce a gain of two, the MAX465/MAX466 exhibit a 1kΩ disabled output resis- tance. LE determines whether E independently. When the latch-enable input (LE) is con- — ...
Page 11
RGB Video Switches and Buffers Table 1a. Amplifier and Channel Selection with — – — – FUNCTION Enables amplifier outputs Selects channel A. Enables amplifier outputs ...
Page 12
Two-Channel, Triple/Quad RGB Video Switches and Buffers MAX467–MAX470 P-P AT 10MHz (a) MAX463–MAX466 * 10MHz (c) Figure ...
Page 13
RGB Video Switches and Buffers 75 1 GND 2 IN1A 75 3 MAX464 GND 4 IN2A 75 5 GND 6 IN3A 75 7 V– –5V 8 IN0B 75 9 V– –5V 10 IN1B 75 11 GND 12 IN2B 75 13 ...
Page 14
Two-Channel, Triple/Quad RGB Video Switches and Buffers 75 1 GND 2 IN1A 75 3 GND 4 IN2A 75 5 GND 6 IN3A 75 7 V– –5V 8 IN0B 75 9 V– –5V 10 IN1B 75 11 GND 12 IN2B 75 ...
Page 15
... RGB + Sync Signal Inputs Figure 8 shows a 1-of-4 RGB + sync video mux/amp circuit. The 1kΩ disabled output resistance limits the number of paralleled MAX465/MAX466s to no more than two. The amplifier outputs are connected after a 22Ω isolation resistor and ahead of a 50Ω back-termi- nation resistor, which isolates the active amplifier out- put from the capacitive load (5pF typ) presented by the inactive output of the second MAX466 ...
Page 16
... MAX464ENI -40°C to +85°C MAX464EWI -40°C to +85°C MAX465CNG 0°C to +70°C 75 MAX465CWG 0°C to +70°C MAX465C/D 0°C to +70°C MAX465ENG -40°C to +85°C MAX465EWG -40°C to +85°C 75 MAX466CNI 0°C to +70°C MAX466CWI 0°C to +70°C MAX466C/D 0°C to +70°C 75 MAX466ENI -40° ...