ncp699 ON Semiconductor, ncp699 Datasheet
ncp699
Available stocks
Related parts for ncp699
ncp699 Summary of contents
Page 1
... PMOS power transistor, internal resistors for setting output voltage, current limit, and temperature limit protection circuits. The NCP699 has been designed to be used with low cost capacitors. The device is housed in the micro-miniature TSOP-5 surface mount package. Standard voltage versions are 1.3, 1.5, 1.8, 2.5, 2.8, 3.0, 3.1, 3 ...
Page 2
... Latch-up capability (85°C) "200 mA DC with trigger voltage. THERMAL CHARACTERISTICS Rating Junction-to-Ambient PSIJ-Lead 2 NOTE: Single component mounted 1.5 mm FR4 PCB with stated copper head spreading area. Using the following boundary conditions as stated in EIA/JESD 51- 12. NCP699 Description Symbol V in Enable V out ...
Page 3
... Decreasing, Output Turns Off, Logic Low) Output Voltage Temperature Coefficient 3. Maximum package power dissipation limits must be observed. T J(max qJA 4. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible. NCP699 = 1 out(nom ...
Page 4
... T , AMBIENT TEMPERATURE (°C) A Figure 4. Quiescent Current vs. Temperature 1.0 2.0 3.0 4.0 V INPUT VOLTAGE (V) in, Figure 6. Ground Pin Current vs. Input Voltage NCP699 TYPICAL CHARACTERISTICS 3.015 3.010 3.005 3.000 2.995 3.0 V out out 150 mA out out 2.990 60 ...
Page 5
... FREQUENCY (Hz) Figure 8. Output Noise Density Figure 10. Load Transient Response 3.5 3.0 2.5 2.0 1.5 1.0 0 NCP699 TYPICAL CHARACTERISTICS out out 100k 1.0M Figure 9. Line Transient Response I = 1.0 mA out 150 mA T 1.0 2.0 3.0 4 INPUT VOLTAGE (V) in Figure 12. Output Voltage vs. Input Voltage http://onsemi ...
Page 6
... IC operation, bias, etc. When the LDO becomes loaded, this term is called the Ground current actually the difference between the input current (measured through the LDO input pin) and the output current. NCP699 DEFINITIONS Line Regulation The change in output voltage for a change in input voltage. ...
Page 7
... P tot + [ gnd (@I out ) ] ) [ out ] * I out or V inMAX + If an 150 mA output current is needed then the ground current from the data sheet is 40 mA. For an NCP699 (3.0 V), the maximum input voltage will then be 5.65 V. http://onsemi.com 7 T J(max ...
Page 8
... NCP699SN15T1G NCP699SN18T1G NCP699SN25T1G NCP699SN28T1G NCP699SN30T1G NCP699SN31T1G NCP699SN33T1G NCP699SN50T1G *Additional voltages in 100 mV steps are available upon request by contacting your ON Semiconductor representative. †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specification Brochure, BRD8011/D. ...
Page 9
... IN THIS LOCATION. TRIMMED LEAD NOT TO EXTEND MORE THAN 0.2 FROM BODY. MILLIMETERS DIM MIN MAX A 3.00 BSC B 1.50 BSC C 0.90 1.10 D 0.25 0.50 G 0.95 BSC H 0.01 0.10 J 0.10 0.26 K 0.20 0.60 L 1.25 1. 2.50 3.00 2.4 0.094 mm SCALE 10:1 inches ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative NCP699/D ...