PCA9552 Philips Semiconductors, PCA9552 Datasheet
PCA9552
Available stocks
Related parts for PCA9552
PCA9552 Summary of contents
Page 1
... PCA9552 2 16-bit I C LED driver with programmable blink rates Product data sheet Supersedes data of 2003 May 02 Philips Semiconductors INTEGRATED CIRCUITS 2004 Oct 01 ...
Page 2
... LED on and off. This greatly increases the amount of traffic on 2 the I C-bus and uses up one of the master’s timers. The PCA9552 LED Blinker instead requires only the initial set up command to program BLINK RATE 1 and BLINK RATE 2 (i.e., the frequency and duty cycle) for each individual output. From then on, only one ...
Page 3
... Address input 2 LED0–7 LED driver 0–7 V Supply ground SS LED driver 8–15 RESET Active-LOW reset input SCL Serial clock line SDA Serial data line V Supply voltage DD 3 Product data sheet PCA9552 18 RESET 1 LED15 2 17 LED14 3 16 LED13 4 15 LED12 ...
Page 4
... POWER- RESET RESET OSCILLATOR V SS 2004 Oct 01 A0 PWM0 PRESCALER 0 REGISTER REGISTER PWM1 PRESCALER 1 REGISTER REGISTER NOTE: ONLY ONE I/O SHOWN FOR CLARITY Figure 3. Block diagram 4 Product data sheet PCA9552 INPUT REGISTER LED SELECT (LSx) REGISTER 0 1 LEDx BLINK0 BLINK1 SW00787 ...
Page 5
... When set to logic 1 a read is selected, while a logic 0 selects a write operation. CONTROL REGISTER Following the successful acknowledgement of the slave address, the bus master will send a byte to the PCA9552 which will be stored in the Control Register. This register can be read and written via the 2 I C-bus ...
Page 6
... POWER-ON RESET When power is applied to V the PCA9552 in a reset condition until V this point, the reset condition is released and the PCA9552 registers are initialized to their default states, all the outputs in the off state Thereafter, V must be lowered below 0 reset the device. ...
Page 7
... Figure 8). SW00363 Figure 7. Definition of start and stop conditions SLAVE MASTER TRANSMITTER/ TRANSMITTER RECEIVER Figure 8. System configuration 7 Product data sheet PCA9552 SDA SCL P STOP condition SW00365 MASTER TRANSMITTER/ MULTIPLEXER ...
Page 8
... In this event, the transmitter must leave the data line HIGH to enable the master to generate a stop condition. DATA OUTPUT BY TRANSMITTER DATA OUTPUT BY RECEIVER SCL FROM MASTER S START condition 2004 Oct 01 not acknowledge acknowledge Figure 9. Acknowledgement on the I C-bus 8 Product data sheet PCA9552 9 clock pulse for acknowledgement SW00368 ...
Page 9
... A1 A0 DATA R/W acknowledge from slave DATA 2 DATA Figure 12. READ input port register 9 Product data sheet PCA9552 data to register DATA 1 A acknowledge from slave DATA 1 VALID t pv SW02000 acknowledge acknowledge from slave from master data from register 1 DATA ...
Page 10
... above V and prevents additional supply current consumption when SW02086 Figure 15. Device supplied by a lower voltage 10 Product data sheet PCA9552 5 V GPIOs SW00930 becomes lower than V and less than the LED supply DD 3 LED ...
Page 11
... LED4 and LED5 to blink 50% duty cycle. LED6 and LED7 will be set to blink and at a 25% duty cycle. LED8 to LED15 will be set to off. Table 1. Start PCA9552 address with A0–A2 = low PSC0 subaddress + auto-increment Set prescaler PSC0 to achieve a period of 1 second: PSC0 1 ...
Page 12
... V; Note 0 5.0 V; Note 3 – — –0.5 2.0 – — Product data sheet PCA9552 MIN MAX UNIT –0.5 6 – 0.5 5 — — 200 mA — 400 mW –65 +150 C –40 +85 C TYP ...
Page 13
... RC time constant of the SDA bus. RESET 13 Product data sheet PCA9552 FAST MODE 2 I C-BUS UNITS MIN MAX 100 0 400 kHz — 1.3 — s — 0.6 — s — 0.6 — ...
Page 14
... MIN –40 Figure 17. Typical frequency variation over process at V 2004 Oct 01 0 +25 +70 TEMPERATURE ( +25 +70 TEMPERATURE ( Product data sheet PCA9552 +20% +10% 0% PERCENT VARIATION –10% –20% –30% –40% +85 SW02311 +20% +10% 0% PERCENT VARIATION –10% –20% –30% –40% ...
Page 15
... Figure 19. Definition of timing BIT 6 BIT 7 (A6) (D1) t HIGH SCL SU;DAT HD;DAT VD;DAT C-bus timing diagram; rise and fall times refer Product data sheet PCA9552 ACK OR READ CYCLE t RESET 50% 50 RESET 50% LED OFF SW02310 t t HD;STA ...
Page 16
... Load capacitance includes jig and probe capacitance Termination resistance should be equal to the output T impedance Z 2004 Oct 500 D.U. FOR SDA AND SCL > the pulse generators. O Figure 21. Test circuitry for switching times 16 Product data sheet PCA9552 V DD Open SW02334 ...
Page 17
... Philips Semiconductors 2 16-bit I C LED driver with programmable blink rates SO24: plastic small outline package; 24 leads; body width 7.5 mm 2004 Oct 01 17 Product data sheet PCA9552 SOT137-1 ...
Page 18
... Philips Semiconductors 2 16-bit I C LED driver with programmable blink rates TSSOP24: plastic thin shrink small outline package; 24 leads; body width 4.4 mm 2004 Oct 01 18 Product data sheet PCA9552 SOT355-1 ...
Page 19
... Philips Semiconductors 2 16-bit I C LED driver with programmable blink rates HVQFN24: plastic thermal enhanced very thin quad flat package; no leads; 24 terminals; body 0.85 mm 2004 Oct 01 19 Product data sheet PCA9552 SOT616-1 ...
Page 20
... Sep 09 (9397 750 10329). _1 20020927 Product data (9397 750 10329); ECN 853-2374 28878 of 09 September 2002. 2004 Oct active connection is used.” C-bus address from ‘25h’ to ‘2Bh’ 2 C-bus address from ‘09h’ to ‘0Ah’ 20 Product data sheet PCA9552 . POR ...
Page 21
... Relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). Fax: + 24825 Document order number: 21 Product data sheet PCA9552 2 C patent Koninklijke Philips Electronics N.V. 2004 All rights reserved. Printed in U.S.A. Date of release: 10-04 ...