595D156X9035D2T Vishay, 595D156X9035D2T Datasheet - Page 8

• Manufacturer Part Number: 595D156X9035D2T
• Description: CAP TANT 15UF 35V 10% SMD
• Manufacturer: Vishay
• Series: TANTAMOUNT® 595Dr
• Type: Conformal Coatedr

Specifications of 595D156X9035D2T

• Capacitance: 15µF
• Voltage - Rated: 35V
• Tolerance: ±10%
• Esr (equivalent Series Resistance): 410.0 mOhm
• Operating Temperature: -55°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 2917 (7343 Metric)
• Size / Dimension: 0.295" L x 0.169" W (7.50mm x 4.30mm)
• Height: 0.110" (2.80mm)
• Manufacturer Size Code: D
• Features: General Purpose
• Voltage Rating, Dc: 35V
• Capacitor Dielectric Type: TANTALUM ELECTROLYTIC
• Tolerance,: 10%
• Tolerance, -: 10%
• Temp, Op. Min: -55(DEGREE C)
• Temp, Op.: ROHS COMPLIANT
• Voltage Rating: 35 Volts
• Esr: 0.41 Ohms
• Operating Temperature Range: - 55 C to + 85 C
• Dimensions: 4.3 mm W x 7.5 mm L
• Mfr Case Code: D Case
• Product: Tantalum Solid Standard Grade - Other Various
• Dissipation Factor Df: 6
• Leakage Current: 5 uAmps
• Ripple Current: 0.43 mAmps
• Termination Style: SMD/SMT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Spacing: -
• Lead Free Status / Rohs Status: Details

PERFORMANCE CHARACTERISTICS
1.
1.1
2.
3.
3.1
3.2
4.
4.1
5.
Document Number: 40007
Revision: 16-Dec-05
Working
Voltage
4 .0
6.3
(V)
10
16
20
25
35
50
- 55 °C
Operating Temperature: Capacitors are designed to
operate over the temperature range of
- 55 °C to + 85 °C.
Capacitors may be operated to + 125 °C with voltage
derating to two-thirds the + 85 °C rating.
DC Working Voltage: The DC working voltage is the
maximum operating voltage for continuous duty at the
rated temperature.
Surge Voltage: The surge DC rating is the maximum
voltage to which the capacitors may be subjected
under any conditions, including transients and peak
ripple at the highest line voltage.
Surge Voltage Test: Capacitors shall withstand the
surge voltage applied in series with a 33 ohm ± 5 %
resistor at the rate of one-half minute on, one-half
minute off, at + 85 °C, for 1000 successive test
cycles.
Following the surge voltage test, the dissipation factor
and the leakage current shall meet the initial
requirements; the capacitance shall not have
changed more than ± 10 %.
Capacitance Tolerance: The capacitance of all
capacitors shall be within the specified tolerance
limits of the normal rating.
Capacitance measurements shall be made by means
of polarized capacitance bridge. The polarizing
voltage shall be of such magnitude that there shall be
no reversal of polarity due to the AC component. The
maximum voltage applied to capacitors during
measurement shall be 2 volts rms at 120 Hz at
+ 25 °C. If the AC voltage applied is less than one-half
volt rms, no DC bias is required. Accuracy of the
bridge shall be within ± 2 %.
Capacitance Change With Temperature: The
capacitance change with temperature shall not
exceed the following percentage of the capacitance
measured at + 25 °C:
- 10 %
+ 85 °C RATING
Voltage
Surge
(V)
5.2
8.0
13
20
26
32
46
65
+ 85 °C
+ 10 %
Working
Voltage
(V)
2.7
4.0
7.0
10
13
17
23
33
+ 125 °C RATING
For technical questions, contact: [e-mail]
TANTAMOUNT® Conformal Coated,
Solid Tantalum Chip Capacitors
+ 125 °C
+ 12 %
Voltage
Surge
3.4
5.0
8.0
(V)
12
16
20
28
38
Maximum CV
6.
6.1
7.
7.1
7.2
7.3
TYPICAL LEAKAGE CURRENT FACTOR RANGE
Dissipation
determined from the expression 2πfRC, shall not
exceed values listed in the Standard Ratings Table.
Measurements shall be made by the bridge method
at, or referred to, a frequency of 120 Hz and a
temperature of + 25 °C.
Leakage Current: Capacitors shall be stabilized at
the rated temperature for 30 minutes. Rated voltage
shall be applied to capacitors for 5 minutes using a
steady source of power (such as a regulated power
supply) with 1000 ohm resistor connected in series
with the capacitor under test to limit the charging
current. Leakage current shall then be measured.
Note that the leakage current varies with temperature
and applied voltage. See graph below for the
appropriate adjustment factor.
At + 25 °C, the leakage current shall not exceed the
value listed in the Standard Ratings Table.
At + 85 °C, the leakage current shall not exceed 10
times the value listed in the Standard Ratings Table.
At + 125 °C, the leakage current shall not exceed 12
times the value listed in the Standard Ratings Table.
0.001
0.01
100
1.0
0.1
10
0
10
20
Factor:
30
Percent of Rated Voltage
40
50
The
Vishay Sprague
60
+ 125 °C
dissipation
70
80
- 55 °C
www.vishay.com
+ 25 °C
+ 85 °C
+ 55 °C
0 °C
90 100
595D
factor,
8