P6KE13A ON Semiconductor, P6KE13A Datasheet - Page 4
![TVS ZENER UNIDIR 600W 13V AXIAL](/photos/10/64/106478/surmeticp6ke_6_8a_sml.jpg)
P6KE13A
Manufacturer Part Number
P6KE13A
Description
TVS ZENER UNIDIR 600W 13V AXIAL
Manufacturer
ON Semiconductor
Series
Surmetic™r
Datasheet
1.P6KE6.8ARLG.pdf
(5 pages)
Specifications of P6KE13A
Voltage - Reverse Standoff (typ)
11.1V
Voltage - Breakdown
12.4V
Power (watts)
600W
Polarization
Unidirectional
Mounting Type
Through Hole
Package / Case
Axial
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Other names
P6KE13AOS
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
P6KE13A
Manufacturer:
PANJIT/ 强茂
Quantity:
20 000
Part Number:
P6KE13A-E3
Manufacturer:
VISHAY/威世
Quantity:
20 000
Company:
Part Number:
P6KE13A-E3/54
Manufacturer:
VISHAY
Quantity:
20 000
Company:
Part Number:
P6KE13AG
Manufacturer:
ON
Quantity:
30 000
Company:
Part Number:
P6KE13ARLG
Manufacturer:
ON
Quantity:
45 000
Company:
Part Number:
P6KE13ARLG
Manufacturer:
ON
Quantity:
30 000
RESPONSE TIME
placed in parallel with the equipment or component to be
protected. In this situation, there is a time delay associated with
the capacitance of the device and an overshoot condition
associated with the inductance of the device and the inductance
of the connection method. The capacitance effect is of minor
importance in the parallel protection scheme because it only
produces a time delay in the transition from the operating
voltage to the clamp voltage as shown in Figure 7.
time (time required for the device to go from zero current to full
current) and lead inductance. This inductive effect produces an
overshoot in the voltage across the equipment or component
being protected as shown in Figure 8. Minimizing this
overshoot is very important in the application, since the main
purpose for adding a transient suppressor is to clamp voltage
spikes. The P6KE6.8A series has very good response time,
typically < 1 ns and negligible inductance. However, external
inductive effects could produce unacceptable overshoot.
Proper circuit layout, minimum lead lengths and placing the
Underwriters Laboratory Recognition for the classification of
protectors (QVGQ2) under the UL standard for safety 497B
and File #E210057. Many competitors only have one or two
devices recognized or have recognition in a non-protective
category. Some competitors have no recognition at all. With
the UL497B recognition, our parts successfully passed several
V
In most applications, the transient suppressor device is
The inductive effects in the device are due to actual turn-on
The entire series including the bidirectional CA suffix has
t
D
= TIME DELAY DUE TO CAPACITIVE EFFECT
V
in
Figure 7.
t
d
V
V
in
V
in
(TRANSIENT)
L
TYPICAL PROTECTION CIRCUIT
t
Z
in
APPLICATION NOTES
UL RECOGNITION*
http://onsemi.com
4
suppressor device as close as possible to the equipment or
components to be protected will minimize this overshoot.
prevent overstress of the protection device. This impedance
should be as high as possible, without restricting the circuit
operation.
DUTY CYCLE DERATING
and at a lead temperature of 25°C. If the duty cycle increases,
the peak power must be reduced as indicated by the curves of
Figure 6. Average power must be derated as the lead or ambient
temperature rises above 25°C. The average power derating
curve normally given on data sheets may be normalized and
used for this purpose.
in error as the 10 ms pulse has a higher derating factor than the
10 ms pulse. However, when the derating factor for a given
pulse of Figure 6 is multiplied by the peak power value of
Figure 1 for the same pulse, the results follow the expected
trend.
tests including Strike Voltage Breakdown test, Endurance
Conditioning, Temperature test, Dielectric Voltage-Withstand
test, Discharge test and several more.
test for the package material, we have been recognized for
much more to be included in their protector category.
*Applies to P6KE6.8A − P6KE200A.
V
Some input impedance represented by Z
The data of Figure 1 applies for non-repetitive conditions
At first glance the derating curves of Figure 6 appear to be
Whereas, some competitors have only passed a flammability
LOAD
OVERSHOOT DUE TO
INDUCTIVE EFFECTS
V
L
Figure 8.
V
in
V
in
L
(TRANSIENT)
is essential to
t