PIC16F716-I/SO Microchip Technology, PIC16F716-I/SO Datasheet - Page 31

IC PIC MCU FLASH 2KX14 18SOIC

PIC16F716-I/SO

Manufacturer Part Number
PIC16F716-I/SO
Description
IC PIC MCU FLASH 2KX14 18SOIC
Manufacturer
Microchip Technology
Series
PIC® 16Fr

Specifications of PIC16F716-I/SO

Program Memory Type
FLASH
Program Memory Size
3.5KB (2K x 14)
Package / Case
18-SOIC (7.5mm Width)
Core Processor
PIC
Core Size
8-Bit
Speed
20MHz
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
13
Ram Size
128 x 8
Voltage - Supply (vcc/vdd)
2 V ~ 5.5 V
Data Converters
A/D 4x8b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Processor Series
PIC16F
Core
PIC
Data Bus Width
8 bit
Data Ram Size
128 B
Interface Type
RS- 232/USB
Maximum Clock Frequency
20 MHz
Number Of Programmable I/os
13
Number Of Timers
3
Operating Supply Voltage
2 V to 5.5 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
52715-96, 52716-328, 52717-734
Development Tools By Supplier
PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000
Minimum Operating Temperature
- 40 C
On-chip Adc
4-ch x 8-bit
Package
18SOIC W
Device Core
PIC
Family Name
PIC16
Maximum Speed
20 MHz
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
XLT18SO-1 - SOCKET TRANSITION 18SOIC 300MILI3-DB16F716 - BOARD DAUGHTER ICEPIC3AC162054 - HEADER INTERFACE ICD2 16F716AC164010 - MODULE SKT PROMATEII DIP/SOIC
Eeprom Size
-
Connectivity
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
PIC16F716-I/SO
Manufacturer:
MICROCHI
Quantity:
42
Part Number:
PIC16F716-I/SO
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Part Number:
PIC16F716-I/SO
0
Company:
Part Number:
PIC16F716-I/SO
Quantity:
2 000
Company:
Part Number:
PIC16F716-I/SO
Quantity:
1 680
5.0
The Timer1 module timer/counter has the following
features:
• 16-bit timer/counter
• Readable and writable (Both registers)
• Internal or external clock select
• Interrupt on overflow from FFFFh to 0000h
• Reset from ECCP module trigger
Timer1 has a control register, shown in Register 5-1.
Timer1 can be enabled/disabled by setting/clearing
control bit TMR1ON (T1CON<0>).
Figure 5-1 is a simplified block diagram of the Timer1
module.
Additional information on timer modules is available in
the
(DS33023).
REGISTER 5-1:
 2003 Microchip Technology Inc.
(Two 8-bit registers; TMR1H and TMR1L)
PICmicro
TIMER1 MODULE
bit 7-6
bit 5-4
bit 3
bit 2
bit 1
bit 0
®
Mid-Range
Unimplemented: Read as '0'
T1CKPS1:T1CKPS0: Timer1 Input Clock Prescale Select bits
11 = 1:8 Prescale value
10 = 1:4 Prescale value
01 = 1:2 Prescale value
00 = 1:1 Prescale value
T1OSCEN: Timer1 Oscillator Enable Control bit
1 = Oscillator is enabled
0 = Oscillator is shut off
T1SYNC: Timer1 External Clock Input Synchronization Control bit
TMR1CS = 1
1 = Do not synchronize external clock input
0 = Synchronize external clock input
TMR1CS = 0
This bit is ignored. Timer1 uses the internal clock when TMR1CS = 0.
TMR1CS: Timer1 Clock Source Select bit
1 = External clock from pin RB1/T1OSO/T1CKI (on the rising edge after the first falling edge)
0 = Internal clock (F
TMR1ON: Timer1 On bit
1 = Enables Timer1
0 = Stops Timer1
Note 1:
Legend:
R = Readable bit
-n = Value at POR
bit 7
T1CON: TIMER1 CONTROL REGISTER (ADDRESS: 10h)
U-0
The oscillator inverter and feedback resistor are turned off to eliminate power drain.
Reference
U-0
OSC
(1)
/4)
T1CKPS1 T1CKPS0
Manual,
R/W-0
W = Writable bit
‘1’ = Bit is set
Preliminary
R/W-0
5.1
Timer1 can operate in one of these modes:
• As a timer
• As a synchronous counter
• As an asynchronous counter
The operating mode is determined by the clock select
bit, TMR1CS (T1CON<1>).
In Timer mode, Timer1 increments every instruction
cycle. In Counter mode, it increments on every rising
edge of the external clock input.
When the Timer1 oscillator is enabled (T1OSCEN is
set), the RB2/T1OSI and RB1/T1OSO/T1CKI pins
become inputs. That is, the TRISB<2:1> value is
ignored.
Timer1 also has an internal “Reset input”. This Reset
can be generated by the ECCP module
(Section 7.0 “Enhanced Capture/Compare/PWM
(ECCP) Module”).
T1OSCEN
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
Timer1 Operation
R/W-0
T1SYNC TMR1CS TMR1ON
R/W-0
PIC16F716
x = Bit is unknown
R/W-0
DS41206A-page 29
R/W-0
bit 0

Related parts for PIC16F716-I/SO