PIC16LF1939-I/ML Microchip Technology, PIC16LF1939-I/ML Datasheet - Page 229

• Manufacturer Part Number: PIC16LF1939-I/ML
• Description: IC MCU 8BIT FLASH 44QFN
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 16Fr

Specifications of PIC16LF1939-I/ML

• Core Size: 8-Bit
• Program Memory Size: 28KB (16K x 14)
• Core Processor: PIC
• Speed: 32MHz
• Connectivity: I²C, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LCD, POR, PWM, WDT
• Number Of I /o: 36
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 14x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-QFN
• Controller Family/series: PIC16LF
• Eeprom Memory Size: 256Byte
• Ram Memory Size: 1024Byte
• Cpu Speed: 32MHz
• No. Of Timers: 5
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

22.4.6.1
The STRxSYNC bit of the PSTRxCON register gives
the user two selections of when the steering event will
happen. When the STRxSYNC bit is ‘0’, the steering
event will happen at the end of the instruction that
writes to the PSTRxCON register. In this case, the
output signal at the Px<D:A> pins may be an
incomplete PWM waveform. This operation is useful
when the user firmware needs to immediately remove
a PWM signal from the pin.
When the STRxSYNC bit is ‘1’, the effective steering
update will happen at the beginning of the next PWM
period. In this case, steering on/off the PWM output will
always produce a complete PWM waveform.
Figures 22-19 and 22-20 illustrate the timing diagrams
of the PWM steering depending on the STRxSYNC
setting.
22.4.7
When any PWM mode is used, the application
hardware must use the proper external pull-up and/or
pull-down resistors on the PWM output pins.
The CCPxM<1:0> bits of the CCPxCON register allow
the user to choose whether the PWM output signals are
active-high or active-low for each pair of PWM output
pins (PxA/PxC and PxB/PxD). The PWM output
polarities must be selected before the PWM pin output
FIGURE 22-19:
FIGURE 22-20:
 2009 Microchip Technology Inc.
P1<D:A>
P1<D:A>
STRx
PWM
STRx
PWM
START-UP CONSIDERATIONS
Steering Synchronization
PORT Data
EXAMPLE OF STEERING EVENT AT END OF INSTRUCTION (STRxSYNC = 0)
EXAMPLE OF STEERING EVENT AT BEGINNING OF INSTRUCTION
(STRxSYNC = 1)
PWM Period
PORT Data
Preliminary
P1n = PWM
drivers
configuration while the PWM pin output drivers are
enable is not recommended since it may result in
damage to the application circuits.
The PxA, PxB, PxC and PxD output latches may not be
in the proper states when the PWM module is
initialized. Enabling the PWM pin output drivers at the
same time as the Enhanced PWM modes may cause
damage to the application circuit. The Enhanced PWM
modes must be enabled in the proper Output mode and
complete a full PWM cycle before enabling the PWM
pin output drivers. The completion of a full PWM cycle
is indicated by the TMRxIF bit of the PIRx register
being set as the second PWM period begins.
P1n = PWM
PIC16F193X/LF193X
Note:
are
When the microcontroller is released from
Reset, all of the I/O pins are in the
high-impedance state. The external cir-
cuits must keep the power switch devices
in the Off state until the microcontroller
drives the I/O pins with the proper signal
levels or activates the PWM output(s).
enabled.
PORT Data
Changing
PORT Data
DS41364D-page 229
the
polarity