PIC16LF72-I/ML Microchip Technology, PIC16LF72-I/ML Datasheet - Page 46

• Manufacturer Part Number: PIC16LF72-I/ML
• Description: IC PIC MCU FLASH 2KX14 28QFN
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16LF72-I/ML

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SPI
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 22
• Program Memory Size: 3.5KB (2K x 14)
• Program Memory Type: FLASH
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 5x8b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-VQFN Exposed Pad, 28-HVQFN, 28-SQFN, 28-DHVQFN
• Lead Free Status / RoHS Status: Request inventory verification / Request inventory verification
• Eeprom Size: -

PIC16F72
REGISTER 9-1:
DS39597C-page 44
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
SSPSTAT: SYNCHRONOUS SERIAL PORT STATUS REGISTER (ADDRESS 94h)
bit 7
SMP: SPI Data Input Sample Phase bits
SPI Master mode:
1 = Input data sampled at end of data output time
0 = Input data sampled at middle of data output time (Microwire
SPI Slave mode:
SMP must be cleared when SPI is used in Slave mode
I
This bit must be maintained clear
CKE: SPI Clock Edge Select bits (Figure 9-2, Figure 9-3, and Figure 9-4)
SPI mode, CKP = 0:
1 = Data transmitted on rising edge of SCK (Microwire alternate)
0 = Data transmitted on falling edge of SCK
SPI mode, CKP = 1:
1 = Data transmitted on falling edge of SCK (Microwire default)
0 = Data transmitted on rising edge of SCK
I
This bit must be maintained clear
D/A: Data/Address bit (I
1 = Indicates that the last byte received or transmitted was data
0 = Indicates that the last byte received or transmitted was address
P: STOP bit (I
the START bit is detected last. SSPEN is cleared.
1 = Indicates that a STOP bit has been detected last (this bit is ‘0’ on RESET)
0 = STOP bit was not detected last
S: START bit (I
the STOP bit is detected last. SSPEN is cleared.
1 = Indicates that a START bit has been detected last (this bit is ‘0’ on RESET)
0 = START bit was not detected last
R/W: Read/Write Information bit (I
ing the last address match. This bit is only valid from the address match to the next START bit,
STOP bit, or ACK bit.
1 = Read
0 = Write
UA: Update Address bit (10-bit I
1 = Indicates that the user needs to update the address in the SSPADD register
0 = Address does not need to be updated
BF: Buffer Full Status bit
Receive (SPI and I
1 = Receive complete, SSPBUF is full
0 = Receive not complete, SSPBUF is empty
Transmit (I
1 = Transmit in progress, SSPBUF is full
0 = Transmit complete, SSPBUF is empty
Legend:
R = Readable bit
- n = Value at POR
2
2
C mode:
C mode:
R/W-0
SMP
2
C mode only):
R/W-0
2
CKE
C mode only) – This bit is cleared when the SSP module is disabled, or when
2
C mode only) – This bit is cleared when the SSP module is disabled, or when
2
C modes):
2
C mode only)
R-0
D/A
W = Writable bit
‘1’ = Bit is set
2
C mode only)
2
C mode only) – This bit holds the R/W bit information follow-
R-0
P
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
R-0
S
R/W
®
R-0
© 2007 Microchip Technology Inc.
)
x = Bit is unknown
R-0
UA
R-0
BF
bit 0