PIC18F25J11-I/ML Microchip Technology, PIC18F25J11-I/ML Datasheet - Page 33

• Manufacturer Part Number: PIC18F25J11-I/ML
• Description: IC PIC MCU FLASH 32K 2V 28-QFN
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F25J11-I/ML

• Core Size: 8-Bit
• Program Memory Size: 32KB (16K x 16)
• Core Processor: PIC
• Speed: 48MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 16
• Program Memory Type: FLASH
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2.15 V ~ 3.6 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-VQFN Exposed Pad, 28-HVQFN, 28-SQFN, 28-DHVQFN
• Controller Family/series: PIC18
• No. Of I/o's: 16
• Ram Memory Size: 3.6875KB
• Cpu Speed: 48MHz
• No. Of Timers: 5
• Interface: EUSART, I2C, SPI
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3776 B
• Interface Type: EUSART, I2C, SPI
• Maximum Clock Frequency: 48 MHz
• Number Of Timers: 5
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DM183022, DM183032, DV164136, MA180023
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 10 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC164322 - MODULE SOCKET MPLAB PM3 28/44QFN
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

2.2.2
In HS and HSPLL Oscillator modes, a crystal or
ceramic resonator is connected to the OSC1 and
OSC2 pins to establish oscillation. Figure 2-2 displays
the pin connections.
The oscillator design requires the use of a parallel cut
crystal.
FIGURE 2-2:
TABLE 2-2:
© 2009 Microchip Technology Inc.
Capacitor values are for design guidance only.
These capacitors were tested with the resonators
listed below for basic start-up and operation. These
values are not optimized.
Different capacitor values may be required to produce
acceptable oscillator operation. The user should test
the performance of the oscillator over the expected
V
See the notes following Table 2-3 for additional
information.
Note 1:
Note:
DD
Mode
HS
and temperature range for the application.
C1
C2
2:
3:
(1)
(1)
Typical Capacitor Values Used:
CRYSTAL OSCILLATOR/CERAMIC
RESONATORS
Use of a series cut crystal may give a fre-
quency out of the crystal manufacturer’s
specifications.
See Table 2-2 and Table 2-3 for initial values
of C1 and C2.
A series resistor (R
strip cut crystals.
R
16.0 MHz
XTAL
R
F
8.0 MHz
S
varies with the selected oscillator mode.
Freq
(2)
Resonators Used:
CAPACITOR SELECTION FOR
CERAMIC RESONATORS
OSC2
OSC1
16.0 MHz
CRYSTAL/CERAMIC
RESONATOR OPERATION
(HS OR HSPLL
CONFIGURATION)
4.0 MHz
8.0 MHz
S
OSC1
27 pF
22 pF
R
) may be required for AT
PIC18F46J11
F
(3)
Sleep
OSC2
27 pF
22 pF
To
Internal
Logic
PIC18F46J11 FAMILY
TABLE 2-3:
An internal postscaler allows users to select a clock
frequency other than that of the crystal or resonator.
Frequency division is determined by the CPDIV
Configuration bits. Users may select a clock frequency
of the oscillator frequency, or 1/2, 1/3 or 1/6 of the
frequency.
Capacitor values are for design guidance only.
These capacitors were tested with the crystals listed
below for basic start-up and operation. These values
are not optimized.
Different capacitor values may be required to produce
acceptable oscillator operation. The user should test
the performance of the oscillator over the expected
V
See the notes following this table for additional
information.
Osc Type
DD
Note 1: Higher capacitance not only increases
HS
and temperature range for the application.
2: Since each resonator/crystal has its own
3: Rs may be required to avoid overdriving
4: Always verify oscillator performance over
the stability of oscillator, but also
increases the start-up time.
characteristics, the user should consult
the resonator/crystal manufacturer for
appropriate
components.
crystals with low drive level specification.
the V
expected for the application.
20 MHz
Crystal
4 MHz
8 MHz
Freq
CAPACITOR SELECTION FOR
CRYSTAL OSCILLATOR
DD
Crystals Used:
and temperature range that is
20 MHz
4 MHz
8 MHz
Typical Capacitor Values
values
27 pF
22 pF
15 pF
C1
Tested:
DS39932C-page 33
of
27 pF
22 pF
15 pF
external
C2