PIC18F26J11-I/SS Microchip Technology, PIC18F26J11-I/SS Datasheet - Page 335

• Manufacturer Part Number: PIC18F26J11-I/SS
• Description: IC PIC MCU FLASH 64K 2V 28-SSOP
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F26J11-I/SS

• Core Size: 8-Bit
• Program Memory Size: 64KB (32K x 16)
• Core Processor: PIC
• Speed: 48MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 16
• Program Memory Type: FLASH
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2.15 V ~ 3.6 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SSOP
• Controller Family/series: PIC18
• No. Of I/o's: 16
• Ram Memory Size: 3.6875KB
• Cpu Speed: 48MHz
• No. Of Timers: 2
• Interface: EUSART, I2C, SPI
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3776 B
• Interface Type: EUSART, I2C, SPI
• Maximum Clock Frequency: 48 MHz
• Number Of Timers: 5
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DV164136, DM183032, MA180023, DM183022
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 10 Channel
• Package: 28SSOP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 48 MHz
• Operating Supply Voltage: 2.5|3.3 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC164322 - MODULE SOCKET MPLAB PM3 28/44QFN
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

The WUE bit is automatically cleared once a
low-to-high transition is observed on the RXx line
following the wake-up event. At this point, the EUSART
module is in Idle mode and returns to normal operation.
This signals to the user that the Sync Break event is
over.
19.2.4.1
Since auto-wake-up functions by sensing rising edge
transitions on RXx/DTx, information with any state
changes before the Stop bit may signal a false
End-Of-Character (EOC) and cause data or framing
errors. To work properly, therefore, the initial character
in the transmission must be all ‘0’s. This can be 00h
(8 bytes) for standard RS-232 devices or 000h
(12 bits) for LIN bus.
Oscillator start-up time must also be considered,
especially in applications using oscillators with
longer start-up intervals (i.e., HS or HSPLL mode).
The Sync Break (or Wake-up Signal) character must
be of sufficient length and be followed by a sufficient
interval to allow enough time for the selected
oscillator to start and provide proper initialization of
the EUSART.
FIGURE 19-8:
FIGURE 19-9:
© 2009 Microchip Technology Inc.
RXx/DTx Line
RXx/DTx Line
Note 1:
WUE bit
WUE bit
Note 1: If the wake-up event requires long oscillator warm-up time, the auto-clear of the WUE bit can occur before the
RCxIF
OSC1
RCxIF
OSC1
2: The EUSART remains in Idle while the WUE bit is set.
(1)
(2)
Special Considerations Using
Auto-Wake-up
The EUSART remains in Idle while the WUE bit is set.
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
oscillator is ready. This sequence should not depend on the presence of Q clocks.
Bit set by user
Bit set by user
SLEEP Command Executed
AUTO-WAKE-UP BIT (WUE) TIMINGS DURING NORMAL OPERATION
AUTO-WAKE-UP BIT (WUE) TIMINGS DURING SLEEP
Q1
Sleep Ends
PIC18F46J11 FAMILY
19.2.4.2
The timing of WUE and RCxIF events may cause some
confusion when it comes to determining the validity of
received data. As noted, setting the WUE bit places the
EUSART in an Idle mode. The wake-up event causes a
receive interrupt by setting the RCxIF bit. The WUE bit
is cleared after this when a rising edge is seen on
RXx/DTx. The interrupt condition is then cleared by
reading the RCREGx register. Ordinarily, the data in
RCREGx will be dummy data and should be discarded.
The fact that the WUE bit has been cleared (or is still
set) and the RCxIF flag is set should not be used as an
indicator of the integrity of the data in RCREGx. Users
should consider implementing a parallel method in
firmware to verify received data integrity.
To assure that no actual data is lost, check the RCIDL
bit to verify that a receive operation is not in process. If
a receive operation is not occurring, the WUE bit may
then be set just prior to entering the Sleep mode.
Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
Cleared due to user read of RCREGx
Cleared due to user read of RCREGx
Special Considerations Using the
WUE Bit
Note 1
DS39932C-page 335
Auto-Cleared
Auto-Cleared