PIC16C711-04/SO Microchip Technology, PIC16C711-04/SO Datasheet - Page 67
![IC MCU OTP 1KX14 A/D 18SOIC](/photos/6/76/67656/150-18-soic_sml.jpg)
PIC16C711-04/SO
Manufacturer Part Number
PIC16C711-04/SO
Description
IC MCU OTP 1KX14 A/D 18SOIC
Manufacturer
Microchip Technology
Series
PIC® 16Cr
Specifications of PIC16C711-04/SO
Program Memory Type
OTP
Program Memory Size
1.75KB (1K x 14)
Package / Case
18-SOIC (7.5mm Width)
Core Processor
PIC
Core Size
8-Bit
Speed
4MHz
Peripherals
Brown-out Detect/Reset, POR, WDT
Number Of I /o
13
Ram Size
68 x 8
Voltage - Supply (vcc/vdd)
4 V ~ 6 V
Data Converters
A/D 4x8b
Oscillator Type
External
Operating Temperature
0°C ~ 70°C
Processor Series
PIC16C
Core
PIC
Data Bus Width
8 bit
Data Ram Size
68 B
Maximum Clock Frequency
4 MHz
Number Of Programmable I/os
13
Number Of Timers
1
Maximum Operating Temperature
+ 70 C
Mounting Style
SMD/SMT
3rd Party Development Tools
52715-96, 52716-328, 52717-734
Development Tools By Supplier
ICE2000
Minimum Operating Temperature
0 C
On-chip Adc
4-ch x 8-bit
Data Rom Size
68 B
Height
2.31 mm
Length
11.53 mm
Supply Voltage (max)
6 V
Supply Voltage (min)
4 V
Width
7.49 mm
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
XLT18SO-1 - SOCKET TRANSITION 18SOIC 300MILISPICR1 - ADAPTER IN-CIRCUIT PROGRAMMING309-1011 - ADAPTER 18-SOIC TO 18-DIP309-1010 - ADAPTER 18-SOIC TO 18-DIPAC164010 - MODULE SKT PROMATEII DIP/SOIC
Eeprom Size
-
Connectivity
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
PIC16C711-04/SO
Manufacturer:
MIC
Quantity:
20 000
FIGURE 8-22: WAKE-UP FROM SLEEP THROUGH INTERRUPT
8.9
If the code protection bit(s) have not been pro-
grammed, the on-chip program memory can be read
out for verification purposes.
8.10
Four memory locations (2000h - 2003h) are designated
as ID locations where the user can store checksum or
other code-identification numbers. These locations are
not accessible during normal execution but are read-
able and writable during program/verify. It is recom-
mended that only the 4 least significant bits of the ID
location are used.
8.11
PIC16CXX microcontrollers can be serially pro-
grammed while in the end application circuit. This is
simply done with two lines for clock and data, and three
other lines for power, ground, and the programming
voltage. This allows customers to manufacture boards
with unprogrammed devices, and then program the
microcontroller just before shipping the product. This
also allows the most recent firmware or a custom firm-
ware to be programmed.
Note 1:
1997 Microchip Technology Inc.
Note:
INSTRUCTION FLOW
INTF flag
(INTCON<1>)
GIE bit
(INTCON<7>)
Instruction
fetched
Instruction
executed
CLKOUT(4)
2:
3:
4:
INT pin
OSC1
Program Verification/Code Protection
ID Locations
In-Circuit Serial Programming
PC
XT, HS or LP oscillator mode assumed.
T
GIE = '1' assumed. In this case after wake- up, the processor jumps to the interrupt routine. If GIE = '0', execution will continue in-line.
CLKOUT is not available in these osc modes, but shown here for timing reference.
Microchip does not recommend code pro-
tecting windowed devices.
OST
Inst(PC) = SLEEP
Q1 Q2 Q3 Q4
= 1024T
Inst(PC - 1)
PC
OSC
(drawing not to scale) This delay will not be there for RC osc mode.
Q1 Q2 Q3 Q4
Inst(PC + 1)
SLEEP
PC+1
Q1
Processor in
SLEEP
PC+2
T
OST
(2)
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
Inst(PC + 2)
Inst(PC + 1)
The device is placed into a program/verify mode by
holding the RB6 and RB7 pins low while raising the
MCLR (V
specification). RB6 becomes the programming clock
and RB7 becomes the programming data. Both RB6
and RB7 are Schmitt Trigger inputs in this mode.
After reset, to place the device into programming/verify
mode, the program counter (PC) is at location 00h. A 6-
bit command is then supplied to the device. Depending
on the command, 14-bits of program data are then sup-
plied to or from the device, depending if the command
was a load or a read. For complete details of serial pro-
gramming, please refer to the PIC16C6X/7X Program-
ming Specifications (Literature #DS30228).
FIGURE 8-23: TYPICAL IN-CIRCUIT SERIAL
PC+2
External
Connector
Signals
Data I/O
CLK
+5V
V
0V
PP
PP
Interrupt Latency
Dummy cycle
) pin from V
(Note 2)
PC + 2
PROGRAMMING
CONNECTION
To Normal
Connections
To Normal
Connections
Q1 Q2 Q3 Q4
IL
PIC16C71X
Inst(0004h)
Dummy cycle
to V
0004h
IHH
(see programming
DS30272A-page 67
V
V
MCLR/V
RB6
RB7
Q1 Q2 Q3 Q4
DD
SS
PIC16CXX
Inst(0005h)
Inst(0004h)
0005h
V
PP
DD