PIC24FJ64GA006-I/PT Microchip Technology, PIC24FJ64GA006-I/PT Datasheet - Page 100

• Manufacturer Part Number: PIC24FJ64GA006-I/PT
• Description: IC PIC MCU FLASH 32KX16 64TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 24Fr

Specifications of PIC24FJ64GA006-I/PT

• Program Memory Type: FLASH
• Program Memory Size: 64KB (22K x 24)
• Package / Case: 64-TFQFP
• Core Processor: PIC
• Core Size: 16-Bit
• Speed: 16MHz
• Connectivity: I²C, PMP, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 53
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC24FJ
• Core: PIC
• Data Bus Width: 16 bit
• Data Ram Size: 8 KB
• Interface Type: I2C/SPI/UART
• Maximum Clock Frequency: 32 MHz
• Number Of Programmable I/os: 53
• Number Of Timers: 5
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52713-733, 52714-737, 53276-922, EWDSPIC
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DM240011, DV164033, MA240013, AC164127, DM240001
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 16-ch x 10-bit
• Controller Family/series: PIC24
• No. Of I/o's: 53
• Ram Memory Size: 8KB
• Cpu Speed: 32MHz
• No. Of Timers: 5
• Embedded Interface Type: I2C, SPI, UART
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DM240011 - KIT STARTER MPLAB FOR PIC24F MCUDV164033 - KIT START EXPLORER 16 MPLAB ICD2MA160011 - DAUGHTER BOARD PICDEM LCD 16F91XDM240001 - BOARD DEMO PIC24/DSPIC33/PIC32AC164327 - MODULE SKT FOR 64TQFP
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC24FJ128GA010 FAMILY
A recommended code sequence for a clock switch
includes the following:
1.
2.
3.
4.
5.
6.
7.
8.
The core sequence for unlocking the OSCCON register
and initiating a clock switch is shown in Example 7-1.
DS39747E-page 100
Disable interrupts during the OSCCON register
unlock and write sequence.
Execute the unlock sequence for the OSCCON
high byte, by writing 78h and 9Ah to
OSCCON<15:8>
instructions.
Write new oscillator source to the NOSC control
bits in the instruction immediately following the
unlock sequence.
Execute the unlock sequence for the OSCCON
low
OSCCON<7:0> in two back-to-back instructions.
Set the OSWEN bit in the instruction immediately
following the unlock sequence.
Continue to execute code that is not clock
sensitive (optional).
Invoke an appropriate amount of software delay
(cycle counting) to allow the selected oscillator
and/or PLL to start and stabilize.
Check to see if OSWEN is ‘0’. If it is, the switch
was successful. If OSWEN is still set, then
check the LOCK bit to determine cause of
failure.
byte
by
writing
in
46h
two
and
back-to-back
57h
to
EXAMPLE 7-1:
;Place the new oscillator selection in W0
;OSCCONH (high byte) Unlock Sequence
MOV
MOV
MOV
MOV.b
MOV.b
;Set new oscillator selection
MOV.b
;OSCCONL (low byte) unlock sequence
MOV
MOV
MOV
MOV.b
MOV.b
;Start oscillator switch operation
BSET OSCCON, #0
#OSCCONH, w1
#0x78, w2
#0x9A, w3
w2, [w1]
w3, [w1]
WREG, OSCCONH
#OSCCONL, w1
#0x46, w2
#0x57, w3
w2, [w1]
w3, [w1]
BASIC CODE SEQUENCE
FOR CLOCK SWITCHING
© 2009 Microchip Technology Inc.