PIC24HJ32GP302-I/SP Microchip Technology, PIC24HJ32GP302-I/SP Datasheet - Page 11
![IC PIC MCU FLASH 32K 28DIP](/photos/6/59/65908/150-28-dip_sml.jpg)
PIC24HJ32GP302-I/SP
Manufacturer Part Number
PIC24HJ32GP302-I/SP
Description
IC PIC MCU FLASH 32K 28DIP
Manufacturer
Microchip Technology
Series
PIC® 24Hr
Datasheets
1.PIC24HJ12GP201-ISO.pdf
(84 pages)
2.PIC24HJ32GP302-ISO.pdf
(368 pages)
3.PIC24HJ32GP302-ISO.pdf
(8 pages)
4.PIC24HJ32GP302-ISO.pdf
(12 pages)
5.PIC24HJ32GP304-EML.pdf
(356 pages)
Specifications of PIC24HJ32GP302-I/SP
Program Memory Type
FLASH
Program Memory Size
32KB (11K x 24)
Package / Case
28-DIP (0.300", 7.62mm)
Core Processor
PIC
Core Size
16-Bit
Speed
40 MIPs
Connectivity
I²C, PMP, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, DMA, POR, PWM, WDT
Number Of I /o
21
Ram Size
4K x 8
Voltage - Supply (vcc/vdd)
3 V ~ 3.6 V
Data Converters
A/D 10x10b/12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Processor Series
PIC24HJ
Core
PIC
Data Bus Width
16 bit
Data Ram Size
4 KB
Interface Type
I2C, SPI, UART
Maximum Clock Frequency
40 MHz
Number Of Programmable I/os
21
Number Of Timers
5
Maximum Operating Temperature
+ 85 C
Mounting Style
Through Hole
3rd Party Development Tools
52713-733, 52714-737, 53276-922, EWDSPIC
Development Tools By Supplier
PG164130, DV164035, DV244005, DV164005, PG164120, DM300027
Minimum Operating Temperature
- 40 C
On-chip Adc
10 bit, 10 Channel / 12 bit, 10 Channel
Controller Family/series
PIC24
No. Of I/o's
21
Ram Memory Size
4KB
Cpu Speed
40MIPS
No. Of Timers
7
Embedded Interface Type
I2C, SPI, UART
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
AC164337 - MODULE SOCKET FOR PM3 40DIP
Eeprom Size
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
FIGURE 3-4:
© 2010 Microchip Technology Inc.
BaseAddress + 0x80
BaseAddress =
No
RemainingCmds = 1368
RemainingCmds =
RemainingCmds – 1
BaseAddress = 0x0
Command to Program
FLOWCHART FOR
PROGRAMMING CODE
MEMORY
RemainingCmds
BaseAddress
PROGP response
Send PROGP
PASS?
Start
‘0’?
End
Is
Is
Yes
Yes
Report Error
No
Failure
3.5.2
After code memory is programmed, the contents of
memory can be verified to ensure that programming
was successful. Verification requires code memory to
be read back and compared against the copy held in
the programmer’s buffer.
The READP command can be used to read back all the
programmed code memory.
Alternatively, you can have the programmer perform
the verification after the entire device is programmed,
using a checksum computation.
3.5.3
Only the Configuration registers are included in the
checksum computation. The Device ID and Unit ID are
not included in the checksum computation.
TABLE D-1: “CHECKSUM COMPUTATION”
how this 16-bit computation can be made for each
dsPIC33F and PIC24H device. Computations for read
code protection are shown both enabled and disabled.
The checksum values shown here assume that the
Configuration registers are also erased. However,
when code protection is enabled, the value of the FGS
register is assumed to be 0x5.
PROGRAMMING VERIFICATION
CHECKSUM COMPUTATION
DS70152H-page 11
shows