DSPIC33FJ64GS606-I/MR Microchip Technology, DSPIC33FJ64GS606-I/MR Datasheet
DSPIC33FJ64GS606-I/MR
Specifications of DSPIC33FJ64GS606-I/MR
Available stocks
Related parts for DSPIC33FJ64GS606-I/MR
DSPIC33FJ64GS606-I/MR Summary of contents
Page 1
... SILICON DEVREV VALUES Part Number dsPIC33FJ32GS406 dsPIC33FJ32GS606 dsPIC33FJ32GS608 dsPIC33FJ32GS610 dsPIC33FJ64GS406 dsPIC33FJ64GS606 dsPIC33FJ64GS608 dsPIC33FJ64GS610 Note 1: The Device IDs (DEVID and DEVREV) are located at the last two implemented addresses of configuration memory space. They are shown in hexadecimal in the format “DEVID DEVREV”. 2: Refer to the “dsPIC33F/PIC24H Flash Programming Specification” (DS70152) for detailed information on Device and Revision IDs for your specific device. © ...
Page 2
... PWM ON time. A glitch may be observed on the PWM pins when the PWM module is enabled after assignment of pin ownership to the PWM module. The ERRIF status bit does not get set when a CAN error condition occurs. (1) Affected Revisions A0 X — © 2010 Microchip Technology Inc. ...
Page 3
... Use the SS1 pin for the slave select function. Affected Silicon Revisions A0 X © 2010 Microchip Technology Inc. 4. Module: JTAG The boundary scan cells for the RD3 and RD13 pins are swapped. When running the boundary scan test, an input to the RD3 pin excites the RD13 pin, and vice versa ...
Page 4
... PWM ON time. Therefore, the PWM period will be reset immediately after the end of the PWM ON time. Work around Ensure that the External Period Reset signal is asserted during the PWM OFF time. Affected Silicon Revisions A0 X specifications #0 dsPIC33FJ64GS406/606/608/610 © 2010 Microchip Technology Inc. ...
Page 5
... Assign pin ownership of PWM1H/RA4 to PWM module IOCON1bits.PENL = 1; // Assign pin ownership of PWM1L/RA3 to PWM module Affected Silicon Revisions A0 X © 2010 Microchip Technology Inc. 2. Assign pin ownership to the GPIO module by configuring IOCONx<PENH> IOCONx<PENL> Specify the PWM override state to the desired safe state for the PWM pins using the OVRDAT< ...
Page 6
... Do not inspect the state of the ERRIF bit to deter- mine if a CAN error interrupt has occurred. Instead, inspect the individual error condition sta- tus flags TXBO, TXBP, RXBP, TXWAR, RXWAR and EWARN (CiINTF<13:8>). Affected Silicon Revisions A0 X DS80489C-page 6 © 2010 Microchip Technology Inc. ...
Page 7
... Input Low Voltage IL DI18 SDAx, SCLx DI19 SDAx, SCLx V Input High Voltage IH DI28 SDAx, SCLx DI29 SDAx, SCLx © 2010 Microchip Technology Inc. specifica- IL Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) -40°C ≤ T Operating temperature -40°C ≤ T Min Typ Max Units V — ...
Page 8
... PWM) and data sheet clarification 1 Characteristics: I/O Pin Input Specifications). Rev C Document (11/2010) Updated the Device IDs in Table 1 for the following devices: • dsPIC33FJ32GS606 • dsPIC33FJ32GS608 • dsPIC33FJ32GS610 • dsPIC33FJ64GS406 • dsPIC33FJ64GS606 • dsPIC33FJ64GS608 Added silicon issue 10 (ECAN). DS80489C-page 8 (High (DC © 2010 Microchip Technology Inc. ...
Page 9
... PICtail, REAL ICE, rfLAB, Select Mode, Total Endurance, TSHARC, UniWinDriver, WiperLock and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. ...
Page 10
... Philippines - Manila Tel: 63-2-634-9065 Fax: 63-2-634-9069 Singapore Tel: 65-6334-8870 Fax: 65-6334-8850 Taiwan - Hsin Chu Tel: 886-3-6578-300 Fax: 886-3-6578-370 Taiwan - Kaohsiung Tel: 886-7-213-7830 Fax: 886-7-330-9305 Taiwan - Taipei Tel: 886-2-2500-6610 Fax: 886-2-2508-0102 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 © 2010 Microchip Technology Inc. 08/04/10 ...