PIC24FJ256GB110-I/PT Microchip Technology, PIC24FJ256GB110-I/PT Datasheet - Page 151
![IC PIC MCU FLASH 256K 100TQFP](/photos/12/13/121330/c04-100-tqfp_sml.jpg)
PIC24FJ256GB110-I/PT
Manufacturer Part Number
PIC24FJ256GB110-I/PT
Description
IC PIC MCU FLASH 256K 100TQFP
Manufacturer
Microchip Technology
Series
PIC® 24Fr
Datasheets
1.PIC24FJ128GA106-IPT.pdf
(52 pages)
2.PIC24FJ64GB106-IPT.pdf
(16 pages)
3.PIC24FJ64GB106-IPT.pdf
(352 pages)
4.PIC24FJ192GB108-IPT.pdf
(328 pages)
Specifications of PIC24FJ256GB110-I/PT
Program Memory Type
FLASH
Program Memory Size
256KB (85.5K x 24)
Package / Case
100-TFQFP
Core Processor
PIC
Core Size
16-Bit
Speed
32MHz
Connectivity
I²C, SPI, UART/USART, USB OTG
Peripherals
Brown-out Detect/Reset, LVD, POR, PWM, WDT
Number Of I /o
83
Ram Size
16K x 8
Voltage - Supply (vcc/vdd)
2 V ~ 3.6 V
Data Converters
A/D 16x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Processor Series
PIC24FJ
Core
PIC
Data Bus Width
16 bit
Data Ram Size
16 KB
Interface Type
I2C/SPI/UART
Maximum Clock Frequency
32 MHz
Number Of Programmable I/os
84
Number Of Timers
5
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
52713-733, 52714-737, 53276-922, EWDSPIC
Development Tools By Supplier
PG164130, DV164035, DV244005, DV164005, PG164120, DM240001, DM240011
Minimum Operating Temperature
- 40 C
On-chip Adc
16-ch x 10-bit
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
876-1004 - PIC24 BREAKOUT BOARDDM240011 - KIT STARTER MPLAB FOR PIC24F MCUMA240014 - MODULE PLUG-IN PIC24DM240001 - BOARD DEMO PIC24/DSPIC33/PIC32
Eeprom Size
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC24FJ256GB110-I/PT
Manufacturer:
MICROCHIP
Quantity:
65 100
Company:
Part Number:
PIC24FJ256GB110-I/PT
Manufacturer:
MICROCHIP
Quantity:
214
Company:
Part Number:
PIC24FJ256GB110-I/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
Part Number:
PIC24FJ256GB110-I/PT
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
11.0
The Timer2/3 and Timer4/5 modules are 32-bit timers,
which can also be configured as four independent 16-bit
timers with selectable operating modes.
As 32-bit timers, Timer2/3 and Timer4/5 can each
operate in three modes:
• Two independent 16-bit timers with all 16-bit
• Single 32-bit timer
• Single 32-bit synchronous counter
They also support these features:
• Timer Gate Operation
• Selectable Prescaler Settings
• Timer Operation during Idle and Sleep modes
• Interrupt on a 32-Bit Period Register Match
• ADC Event Trigger (Timer4/5 only)
Individually, all four of the 16-bit timers can function as
synchronous timers or counters. They also offer the
features listed above, except for the ADC Event
Trigger; this is implemented only with Timer5. The
operating modes and enabled features are determined
by setting the appropriate bit(s) in the T2CON, T3CON,
T4CON and T5CON registers. T2CON and T4CON are
shown in generic form in Register 11-1; T3CON and
T5CON are shown in Register 11-2.
For 32-bit timer/counter operation, Timer2 and Timer4
are the least significant word; Timer3 and Timer4 are
the most significant word of the 32-bit timers.
© 2008 Microchip Technology Inc.
Note:
operating modes (except Asynchronous Counter
mode)
Note:
TIMER2/3 AND TIMER4/5
This data sheet summarizes the features
of this group of PIC24F devices. It is not
intended to be a comprehensive reference
source. For more information, refer to the
“PIC24F
”Section 14. Timers” (DS39704).
For 32-bit operation, T3CON and T5CON
control bits are ignored. Only T2CON and
T4CON control bits are used for setup and
control. Timer2 and Timer4 clock and gate
inputs are utilized for the 32-bit timer
modules, but an interrupt is generated with
the Timer3 or Timer5 interrupt flags.
Family
Reference
Manual”,
PIC24FJ256GB110 FAMILY
Preliminary
To configure Timer2/3 or Timer4/5 for 32-bit operation:
1.
2.
3.
4.
5.
6.
The timer value, at any point, is stored in the register
pair, TMR3:TMR2 (or TMR5:TMR4). TMR3 (TMR5)
always contains the most significant word of the count,
while TMR2 (TMR4) contains the least significant word.
To configure any of the timers for individual 16-bit
operation:
1.
2.
3.
4.
5.
6.
Set the T32 bit (T2CON<3> or T4CON<3> = 1).
Select the prescaler ratio for Timer2 or Timer4
using the TCKPS1:TCKPS0 bits.
Set the Clock and Gating modes using the TCS
and TGATE bits. If TCS is set to external clock,
RPINRx (TxCK) must be configured to an avail-
able RPn pin. See Section 9.4 “Peripheral Pin
Select” for more information.
Load the timer period value. PR3 (or PR5) will
contain the most significant word of the value
while PR2 (or PR4) contains the least significant
word.
If interrupts are required, set the interrupt enable
bit, T3IE or T5IE; use the priority bits,
T3IP2:T3IP0 or T5IP2:T5IP0, to set the interrupt
priority. Note that while Timer2 or Timer4 con-
trols the timer, the interrupt appears as a Timer3
or Timer5 interrupt.
Set the TON bit (= 1).
Clear the T32 bit corresponding to that timer
(T2CON<3>
T4CON<3> for Timer4 and Timer5).
Select the timer prescaler ratio using the
TCKPS1:TCKPS0 bits.
Set the Clock and Gating modes using the TCS
and TGATE bits. See Section 9.4 “Peripheral
Pin Select” for more information.
Load the timer period value into the PRx register.
If interrupts are required, set the interrupt enable
bit, TxIE; use the priority bits, TxIP2:TxIP0, to
set the interrupt priority.
Set the TON bit (TxCON<15> = 1).
for
Timer2
and
DS39897B-page 149
Timer3
or