PIC18LF6520-I/PT Microchip Technology, PIC18LF6520-I/PT Datasheet - Page 75

• Manufacturer Part Number: PIC18LF6520-I/PT
• Description: IC MCU FLASH 16KX16 EEPROM64TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18LF6520-I/PT

• Core Size: 8-Bit
• Program Memory Size: 32KB (16K x 16)
• Core Processor: PIC
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 52
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TFQFP
• Controller Family/series: PIC18
• No. Of I/o's: 52
• Eeprom Memory Size: 1024Byte
• Ram Memory Size: 2KB
• Cpu Speed: 40MHz
• No. Of Timers: 5
• Processor Series: PIC18LF
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: I2C, SPI, USART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 52
• Number Of Timers: 2 x 8 bit
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DV164136, DM183032, DM183022
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

6.2
The External Memory Interface implemented in
PIC18F8X20 devices operates only in 16-bit mode.
The mode selection is not software configurable, but is
programmed via the configuration bits.
The WM<1:0> bits in the MEMCON register determine
three types of connections in 16-bit mode. They are
referred to as:
• 16-bit Byte Write
• 16-bit Word Write
• 16-bit Byte Select
These three different configurations allow the designer
maximum flexibility in using 8-bit and 16-bit memory
devices.
For all 16-bit modes, the Address Latch Enable (ALE)
pin indicates that the address bits A<15:0> are
available on the External Memory Interface bus.
Following the address latch, the Output Enable signal
(OE) will enable both bytes of program memory at once
to form a 16-bit instruction word. The Chip Enable
signal (CE) is active at any time that the microcontroller
accesses external memory, whether reading or writing;
it is inactive (asserted high) whenever the device is in
Sleep mode.
FIGURE 6-1:
 2004 Microchip Technology Inc.
Note 1: This signal only applies to table writes. See Section 5.1 “Table Reads and Table Writes”.
PIC18F8X20
16-bit Mode
AD<15:8>
A<19:16>
AD<7:0>
PIC18F6520/8520/6620/8620/6720/8720
WRH
WRL
ALE
CE
OE
16-BIT BYTE WRITE MODE EXAMPLE
373
373
D<7:0>
A<19:0>
D<15:8>
In Byte Select mode, JEDEC standard Flash memories
will require BA0 for the byte address line and one I/O
line to select between Byte and Word mode. The other
16-bit modes do not need BA0. JEDEC standard static
RAM memories will use the UB or LB signals for byte
selection.
6.2.1
Figure 6-1 shows an example of 16-bit Byte Write
mode for PIC18F8X20 devices. This mode is used for
two separate 8-bit memories connected for 16-bit oper-
ation. This generally includes basic EPROM and Flash
devices. It allows table writes to byte-wide external
memories.
During a TBLWT instruction cycle, the TABLAT data is
presented on the upper and lower bytes of the
AD15:AD0 bus. The appropriate WRH or WRL control
line is strobed on the LSb of the TBLPTR.
16-BIT BYTE WRITE MODE
A<x:0>
D<7:0>
CE
OE
(MSB)
WR
(1)
Address Bus
Data Bus
Control Lines
D<7:0>
DS39609B-page 73
A<x:0>
D<7:0>
CE
OE
(LSB)
WR
(1)