MC908JB8FBE Freescale Semiconductor, MC908JB8FBE Datasheet - Page 102

• Manufacturer Part Number: MC908JB8FBE
• Description: IC MCU 8K FLASH 3MHZ 44-QFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908JB8FBE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 3MHz
• Connectivity: USB
• Peripherals: LVD, POR, PWM
• Number Of I /o: 37
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 44-QFP
• Processor Series: HC08JB
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: USB
• Maximum Clock Frequency: 3 MHz
• Number Of Programmable I/os: 37
• Number Of Timers: 2
• Operating Supply Voltage: 5.25 V
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, DEMO908GZ60E, M68EML08GZE, KITUSBSPIDGLEVME, KITUSBSPIEVME, KIT33810EKEVME
• Minimum Operating Temperature: 0 C
• Controller Family/series: HC08
• No. Of I/o's: 37
• Ram Memory Size: 256Byte
• Cpu Speed: 8MHz
• No. Of Timers: 1
• Embedded Interface Type: SCI, SPI
• Rohs Compliant: Yes
• Package: 44PQFP
• Family Name: HC08
• Maximum Speed: 3 MHz
• Cpu Family: HC08
• Device Core Size: 8b
• Frequency (max): 3MHz
• Total Internal Ram Size: 256Byte
• # I/os (max): 37
• Number Of Timers - General Purpose: 2
• Operating Supply Voltage (typ): 5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 4V
• Instruction Set Architecture: CISC
• Operating Temp Range: 0C to 70C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 44
• Package Type: PQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

System Integration Module (SIM)
8.4.2.5 Low-Voltage Inhibit (LVI) Reset
8.4.2.6 Universal Serial Bus Reset
8.4.2.7 Registers Values After Different Resets
Technical Data
102
NOTE:
The low-voltage inhibit module (LVI) asserts its output to the SIM when
the V
reset status register (RSR) is set, and the external reset pin (RST) is held
low while the SIM counter counts out 4096 OSCXCLK cycles. Sixty-four
OSCXCLK cycles later, the CPU is released from reset to allow the reset
vector sequence to occur. The SIM actively pulls down the RST pin for
all internal reset sources.
The USB module will detect a reset signaled on the bus by the presence
of an extended SE0 at the USB data pins of a device. The MCU seeing
a single-ended 0 on its USB data inputs for more than 2.5
signal as a reset. After the reset is removed, the device will be in the
attached, but not yet addressed or configured, state (refer to Section 9.1
USB Devices of the Universal Serial Bus Specification Rev. 1.1). The
device must be able to accept the device address via a SET_ADDRESS
command (refer to Section 9.4 of the Universal Serial Bus Specification
Rev. 1.1) no later than 10ms after the reset is removed.
USB reset can be disabled to generate an internal reset, instead, a USB
interrupt can be generated. (See
(CONFIG).)
USB reset is disabled when the USB module is disabled by clearing the
USBEN bit of the USB Address Register (UADDR).
Some registers are reset by POR or LVI reset only.
registers or register bits which are unaffected by normal resets.
DD
voltage falls to the LVI reset voltage, V
System Integration Module (SIM)
MC68HC908JB8•MC68HC08JB8•MC68HC08JT8 — Rev. 2.3
Section 5. Configuration Register
TRIP
Freescale Semiconductor
Table 8-3
. The LVI bit in the
µ
s treats that
shows the