MC9S08GT16AMFDE Freescale Semiconductor, MC9S08GT16AMFDE Datasheet - Page 28

• Manufacturer Part Number: MC9S08GT16AMFDE
• Description: IC MCU 16K FLASH 2K RAM 48-QFN
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08GT16AMFDE

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 39
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 48-QFN
• Processor Series: S08GT
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: I2C, IRSCI, SPI
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 39
• Operating Supply Voltage: 3.6 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: M68EVB908GB60E, M68DEMO908GB60E
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit
• Package: 48QFN EP
• Family Name: HCS08
• Maximum Speed: 40 MHz
• For Use With: M68DEMO908GB60E - BOARD DEMO MC9S08GB60M68EVB908GB60E - BOARD EVAL FOR MC9S08GB60
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Pins and Connections
2.3.1
V
I/O buffer circuitry and to an internal voltage regulator. The internal voltage regulator provides regulated
lower-voltage source to the CPU and other internal circuitry of the MCU.
Typically, application systems have two separate capacitors across the power pins. In this case, there
should be a bulk electrolytic capacitor, such as a 10-µF tantalum capacitor, to provide bulk charge storage
for the overall system and a 0.1-µF ceramic bypass capacitor located as close to the MCU power pins as
practical to suppress high-frequency noise.
V
the ATD. A 0.1-µF ceramic bypass capacitor should be located as close to the MCU power pins as practical
to suppress high-frequency noise.
V
performance, they must be connected directly to V
2.3.2
Immediately after reset, the MCU uses an internally generated clock (self-clocked mode — f
is approximately equivalent to an 8-MHz crystal rate. This frequency source is used during reset startup
and can be enabled as the clock source for stop recovery to avoid the need for a long crystal startup delay.
This MCU also contains a trimmable internal clock generator (ICG) module that can be used to run the
MCU. For more information on the ICG, see
The oscillator amplitude on XTAL and EXTAL is gain limited for low-power oscillation. Typically, these
pins have a 1-V peak-to-peak signal. For noisy environments, the high gain output (HGO) bit can be set to
enable rail-to-rail oscillation.
The oscillator in this MCU is a Pierce oscillator that can accommodate a crystal or ceramic resonator in
either of two frequency ranges selected by the RANGE bit in the ICGC1 register. Rather than a crystal or
ceramic resonator, an external oscillator can be connected to the EXTAL input pin, and the XTAL output
pin can be used as general I/O. The external oscillator amplitude must not exceed V
Refer to
resistors such as carbon composition resistors. Wire-wound resistors, and some metal film resistors, have
too much inductance. C1 and C2 normally should be high-quality ceramic capacitors that are specifically
designed for high-frequency applications.
R
value is not generally critical. Typical systems use 1 MΩ to 10 MΩ. Higher values are sensitive to humidity
and lower values reduce gain and (in extreme cases) could prevent startup.
28
F
DD
DDAD
REFH
is used to provide a bias path to keep the EXTAL input in its linear range during crystal startup and its
and V
and V
and V
Figure 2-5
V
References
PTG1/XTAL, PTG2/EXTAL — Oscillator
SS
DD
REFL
SSAD
are the primary power supply pins for the MCU. This voltage source supplies power to all
The 48-pin QFN version of the MC9S08GT16A/GT8A has two adjacent
V
between them.
, V
SS
are the reference voltages for the analog-to-digital converter and for most accurate
pins. Both pins must be connected to ground with zero impedance
are the analog power supply pins for the MCU. This voltage source supplies power to
for the following discussion. R
SS
, V
DDAD
, V
MC9S08GT16A/GT8A Data Sheet, Rev. 1
SSAD
, V
Chapter 9, “Internal Clock Generator
REFH
NOTE
DDAD
S
(when used) and R
, V
REFL
and V
SSAD
— Power and Voltage
with the shortest traces possible.
F
should be low-inductance
(S08ICGV4).”
DD
Freescale Semiconductor
.
Self_reset
), that