PIC16C432-I/SS Microchip Technology, PIC16C432-I/SS Datasheet - Page 56

IC MCU CMOS 8BIT 20MHZ 2K 20SSOP

PIC16C432-I/SS

Manufacturer Part Number
PIC16C432-I/SS
Description
IC MCU CMOS 8BIT 20MHZ 2K 20SSOP
Manufacturer
Microchip Technology
Series
PIC® 16Cr
Datasheets

Specifications of PIC16C432-I/SS

Core Processor
PIC
Core Size
8-Bit
Speed
20MHz
Connectivity
LIN (Local Interconnect Network)
Peripherals
Brown-out Detect/Reset, POR, WDT
Number Of I /o
12
Program Memory Size
3.5KB (2K x 14)
Program Memory Type
OTP
Ram Size
128 x 8
Voltage - Supply (vcc/vdd)
4.5 V ~ 5.5 V
Oscillator Type
External
Operating Temperature
-40°C ~ 85°C
Package / Case
20-SSOP
For Use With
AC164029 - MODULE SKT PROMATEII 20DIP/SSOP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Eeprom Size
-
Data Converters
-
PIC16C432
9.5.1
External interrupt on RB0/INT pin is edge triggered;
either rising if INTEDG bit (OPTION<6>) is set, or fall-
ing, if INTEDG bit is clear. When a valid edge appears
on the RB0/INT pin, the INTF bit (INTCON<1>) is set.
This interrupt can be disabled by clearing the INTE
control bit (INTCON<4>). The INTF bit must be cleared
in software in the Interrupt Service Routine before re-
enabling this interrupt. The RB0/INT interrupt can
wake-up the processor from SLEEP, if the INTE bit was
set prior to going into SLEEP. The status of the GIE bit
decides whether or not the processor branches to the
interrupt vector following wake-up. See Section 9.8 for
details on SLEEP and Figure 9-18 for timing of wake-
up from SLEEP through RB0/INT interrupt.
FIGURE 9-16:
DS41140B-page 54
GIE bit
(INTCON<7>)
INSTRUCTION FLOW
INTF flag
(INTCON<1>)
CLKOUT
INT pin
OSC1
Instruction
Executed
Instruction
Fetched
Note 1: INTF flag is sampled here (every Q1).
PC
2: Interrupt latency = 1-4 Tcy where Tcy = instruction cycle time. Latency is the same whether Inst (PC) is a single
3: CLKOUT is available only in RC Oscillator mode.
4: For minimum width of INT pulse, refer to AC specs.
5: INTF is enabled to be set any time during the Q4-Q1 cycles.
RB0/INT INTERRUPT
3
cycle or a 2-cycle instruction.
Q1
Inst (PC-1)
Inst (PC)
INT PIN INTERRUPT TIMING
1
Q2
PC
Q3
4
Q4
5
Q1
Inst (PC+1)
Inst (PC)
Q2
1
PC+1
Q3
Preliminary
Q4
Interrupt Latency
Q1
Dummy Cycle
Q2
9.5.2
An overflow (FFh
set the T0IF (INTCON<2>) bit. The interrupt can
be
(INTCON<5>) bit. For operation of the Timer0 module,
see Section 6.0.
9.5.3
An input change on PORTB <7:4> sets the RBIF
(INTCON<0>) bit. The interrupt can be enabled/dis-
abled by setting/clearing the RBIE (INTCON<4>) bit.
For operation of PORTB (Section 4.2).
9.5.4
See Section 7.6 for complete description of comparator
interrupts.
PC+1
Note:
Q3
enabled/disabled
Q4
2
If a change on the I/O pin should occur
when the read operation is being executed
(start of the Q2 cycle), then the RBIF inter-
rupt flag may not get set.
TMR0 INTERRUPT
PORTB INTERRUPT
COMPARATOR INTERRUPT
Q1
Dummy Cycle
Inst (0004h)
Q2
0004h
00h) in the TMR0 register will
Q3
by
2002 Microchip Technology Inc.
Q4
setting/clearing
Q1
Inst (0005h)
Q2
Inst (0004h)
0005h
Q3
Q4
T0IE

Related parts for PIC16C432-I/SS