PIC10F206-E/P Microchip Technology, PIC10F206-E/P Datasheet - Page 6

• Manufacturer Part Number: PIC10F206-E/P
• Description: IC PIC MCU FLASH 512X12 8DIP
• Manufacturer: Microchip Technology
• Series: PIC® 10Fr

Specifications of PIC10F206-E/P

• Core Size: 8-Bit
• Program Memory Size: 768B (512 x 12)
• Core Processor: PIC
• Speed: 4MHz
• Peripherals: POR, WDT
• Number Of I /o: 3
• Program Memory Type: FLASH
• Ram Size: 24 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 8-DIP (0.300", 7.62mm)
• Controller Family/series: PIC10
• No. Of I/o's: 4
• Ram Memory Size: 24Byte
• Cpu Speed: 4MHz
• No. Of Timers: 1
• Processor Series: PIC10F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 24 B
• Interface Type: USB
• Maximum Clock Frequency: 4 MHz
• Number Of Programmable I/os: 4
• Number Of Timers: 1
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• For Use With: AC162059 - HEADER INTRFC MPLAB ICD2 8/14PINAC164037 - MODULE SKT 6L PROMATE II SOT23
• Eeprom Size: -
• Data Converters: -
• Connectivity: -
• Lead Free Status / Rohs Status: Details

PIC10F200/202/204/206
3.1.2.5
The End Programming command terminates the
program process. A delay of T
required before the next command to allow the internal
programming voltage to discharge (see Figure 3-6).
FIGURE 3-6:
3.1.2.6
After this command is performed, the entire program
memory and Configuration Word is erased.
To perform a Bulk Erase of the program memory and
configuration fuses, the following sequence must be
performed (see Figure 3-12).
1.
2.
3.
4.
5.
DS41228E-page 6
Note 1: A fully erased part will read ‘1’s in every
Read and save 0x0FF/0x1FF oscillator calibra-
tion bits and 0x104/0x204 backup OSCCAL bits
into computer/programmer temporary memory.
Enter Program/Verify mode. PC is set to Config-
uration Word address.
Perform a Bulk Erase Program Memory
command.
Wait T
Restore OSCCAL bits.
2: The oscillator calibration bits are erased if
ICSPCLK
ICSPDAT
ERA
program memory location.
a Bulk Erase is invoked. They must be
read and saved prior to erasing the
device and restored during the program-
ming operation. Oscillator calibration bits
are stored at the Reset vector as the
operand of a MOVLW instruction.
End Programming
Bulk Erase Program Memory
to complete Bulk Erase.
END PROGRAMMING (EXTERNALLY TIMED)
DIS
1
0
(see Table 6-1) is
2
1
Preliminary
T
3
1
SET
1
4
1
To perform a full device Bulk Erase of the program
memory, configuration fuses, user IDs and backup
OSCCAL value, the following sequence must be
performed (see Figure 3-13).
1.
2.
3.
4.
5.
6.
7.
T
HLD
Read and save 0x0FF/0x1FF oscillator calibra-
tion bits and 0x104/0x204 backup OSCCAL bits
into computer/programmer temporary memory.
Enter Program/Verify mode.
Increment PC to 0x200/0x400 (first user ID
location).
Perform a Bulk Erase command.
Wait T
Restore OSCCAL bits.
Restore backup OSCCAL bits.
5
x
1
ERA
6
x
to complete Bulk Erase.
T
DIS
© 2007 Microchip Technology Inc.
1
Next Command
2