PIC12C508AT-04/SN Microchip Technology, PIC12C508AT-04/SN Datasheet - Page 45
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
PIC12C508AT-04/SN
Manufacturer Part Number
PIC12C508AT-04/SN
Description
IC MCU OTP 512X12 8SOIC
Manufacturer
Microchip Technology
Series
PIC® 12Cr
Datasheets
1.PIC12C508A-04SM.pdf
(113 pages)
2.PIC12C508A-04SM.pdf
(6 pages)
3.PIC12C508A-04SM.pdf
(16 pages)
4.PIC12C508A-04SM.pdf
(4 pages)
Specifications of PIC12C508AT-04/SN
Core Processor
PIC
Core Size
8-Bit
Speed
4MHz
Peripherals
POR, WDT
Number Of I /o
5
Program Memory Size
768B (512 x 12)
Program Memory Type
OTP
Ram Size
25 x 8
Voltage - Supply (vcc/vdd)
3 V ~ 5.5 V
Oscillator Type
Internal
Operating Temperature
0°C ~ 70°C
Package / Case
8-SOIC (3.9mm Width)
For Use With
309-1046 - ADAPTER 8-SOIC TO 8-DIP309-1045 - ADAPTER 8-SOIC TO 8-DIPAC124001 - MODULE SKT PROMATEII 8DIP/SOIC
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Data Converters
-
Connectivity
-
8.9
A device may be powered down (SLEEP) and later
powered up (Wake-up from SLEEP).
8.9.1
The Power-Down mode is entered by executing a
SLEEP instruction.
If enabled, the Watchdog Timer will be cleared but
keeps running, the TO bit (STATUS<4>) is set, the PD
bit (STATUS<3>) is cleared and the oscillator driver is
turned off. The I/O ports maintain the status they had
before the SLEEP instruction was executed (driving
high, driving low, or hi-impedance).
It should be noted that a RESET generated by a WDT
time-out does not drive the MCLR pin low.
For lowest current consumption while powered down,
the T0CKI input should be at V
MCLR/V
MCLR is enabled.
8.9.2
The device can wake-up from SLEEP through one of
the following events:
1.
2.
3.
These events cause a device reset. The TO, PD, and
GPWUF bits can be used to determine the cause of
device reset. The TO bit is cleared if a WDT time-out
occurred (and caused wake-up). The PD bit, which is
set on power-up, is cleared when SLEEP is invoked.
The GPWUF bit indicates a change in state while in
SLEEP at pins GP0, GP1, or GP3 (since the last time
there was a file or bit operation on GP port).
The WDT is cleared when the device wakes from
sleep, regardless of the wake-up source.
Caution: Right before entering SLEEP, read the
1999 Microchip Technology Inc.
An external reset input on GP3/MCLR/V
when configured as MCLR.
A Watchdog Timer time-out reset (if WDT was
enabled).
A change on input pin GP0, GP1, or GP3/
MCLR/V
enabled.
PP
Power-Down Mode (SLEEP)
SLEEP
WAKE-UP FROM SLEEP
input pins. When in SLEEP, wake up
occurs when the values at the pins change
from the state they were in at the last
reading. If a wake-up on change occurs
and
reentering SLEEP, a wake up will occur
immediately even if no pins change while
in SLEEP mode.
pin must be at a logic high level (V
PP
the
when wake-up on change is
pins
are
DD
or V
not
SS
read
and the GP3/
PP
IHMC
before
pin,
) if
8.10
If the code protection bit has not been programmed,
the on-chip program memory can be read out for
verification purposes.
The first 64 locations can be read by the PIC12C5XX
regardless of the code protection bit setting.
The last memory location cannot be read if code pro-
tection is enabled on the PIC12C508/509.
The last memory location can be read regardless of the
code protection bit setting on the PIC12C508A/509A/
CR509A/CE518/CE519.
8.11
Four memory locations are designated as ID locations
where the user can store checksum or other code-
identification numbers. These locations are not
accessible during normal execution but are readable
and writable during program/verify.
Use only the lower 4 bits of the ID locations and
always program the upper 8 bits as ’0’s.
Program Verification/Code Protection
ID Locations
PIC12C5XX
DS40139E-page 45