PIC12C508A-04I/MF Microchip Technology, PIC12C508A-04I/MF Datasheet
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
PIC12C508A-04I/MF
Specifications of PIC12C508A-04I/MF
Related parts for PIC12C508A-04I/MF
PIC12C508A-04I/MF Summary of contents
Page 1
... PIC12C508A/C509A/CR509A PIC12C508A/C509A/CR509A Rev. B Silicon/Data Sheet Errata The PIC12C508A/C509A/CR509A (Rev. B) parts you have received conform functionally to the Device Data Sheet (DS40139), except for the anomalies described below. 1. Valid regions of operation: PIC12LC508A/LC509A/LCR509A VOLTAGE FREQUENCY GRAPH, -40°C ≤ T FIGURE 1: 6.0 5.5 5.0 4 (Volts) 4.0 3 ...
Page 2
... PIC12C508A/C509A/CR509A PIC12LC508A/LC509A/LCR509A VOLTAGE FREQUENCY GRAPH, 0°C ≤ T FIGURE 2: 6.0 5.5 5.0 4 (Volts) 4.0 3.5 3.0 2.5 2.0 0 Note 1: The shaded region indicates the permissible combinations of voltage and frequency. 2: The maximum rated speed of the part limits the permissible combinations of voltage and frequency. ...
Page 3
... Clarifications/Corrections to the Data Sheet: In the Device Data Sheet (DS40139E), the following clarifications and corrections should be noted. 1. Valid regions of operation: PIC12C508A/C509A/CR509A VOLTAGE FREQUENCY GRAPH, -40°C ≤ T FIGURE 4: 6.0 5.5 5.0 4 (Volts) 4.0 3.5 3.0 2.5 0 Note 1: The shaded region indicates the permissible combinations of voltage and frequency. ...
Page 4
... The power-down current in SLEEP mode does not depend on the oscillator type. Power-down current is measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to V DS80063D-page 4 PIC12C508A/509A (Commercial, Industrial, Extended) PIC12CE518/519 (Commercial, Industrial, Extended) PIC12CR509A (Commercial, Industrial, Extended) ...
Page 5
... The power-down current in SLEEP mode does not depend on the oscillator type. Power-down current is measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to V 2003 Microchip Technology Inc. PIC12C508A/C509A/CR509A PIC12LC508A/509A (Commercial, Industrial) PIC12LCE518/519 (Commercial, Industrial) PIC12LCR509A (Commercial, Industrial) ...
Page 6
... This specification applies when GP3/MCLR is configured as an input with pull-up disabled. The leakage current of the MCLR circuit is higher than the standard I/O logic. DS80063D-page 6 PIC12C508A/509A (Commercial, Industrial, Extended) PIC12CE518/519 (Commercial, Industrial, Extended) PIC12CR509A (Commercial, Industrial, Extended) Standard Operating Conditions (unless otherwise specified) 0° ...
Page 7
... This specification applies when GP3/MCLR is configured as an input with pull-up disabled. The leakage current of the MCLR circuit is higher than the standard I/O logic. 2003 Microchip Technology Inc. PIC12C508A/C509A/CR509A PIC12LC508A/509A (Commercial, Industrial) PIC12LCE518/519 (Commercial, Industrial) PIC12LCR509A (Commercial, Industrial) Standard Operating Conditions (unless otherwise specified) 0° ...
Page 8
... PIC12C508A/C509A/CR509A TABLE 13-1: PULL-UP RESISTOR RANGES* - PIC12C508A, PIC12C509A, PIC12CR509A, PIC12CE518, PIC12CE519, PIC12LC508A, PIC12LC509A, PIC12LCR509A, PIC12LCE518 and PIC12LCE519 V DD (Volts) Temperature (°C) 2.5 - 125 5.5 - 125 2.5 - 125 5.5 - 125 * These parameters are characterized but not tested. Note 1: The weak pull-up resistor and associated current for the GP3/MCLR pin is non-linear when the respective ...
Page 9
... Mold Draft Angle Bottom * Controlling Parameter § Significant Characteristic Notes: Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010” (0.254mm) per side. JEDEC Equivalent: MS-001 Drawing No. C04-018 2003 Microchip Technology Inc. PIC12C508A/C509A/CR509A Units ...
Page 10
... PIC12C508A/C509A/CR509A 8-Lead Plastic Small Outline (SM) – Medium, 208 mil (SOIC β Dimension Limits Number of Pins Pitch Overall Height Molded Package Thickness Standoff § Overall Width Molded Package Width Overall Length Foot Length Foot Angle Lead Thickness Lead Width Mold Draft Angle Top ...
Page 11
... Tip to Seating Plane Lead Thickness Upper Lead Width Lower Lead Width Overall Row Spacing § Window Diameter Lid Length Lid Width * Controlling Parameter § Significant Characteristic JEDC Equivalent: MS-015 Drawing No. C04-083 2003 Microchip Technology Inc. PIC12C508A/C509A/CR509A Units INCHES* MIN NOM ...
Page 12
... PIC12C508A/C509A/CR509A 8-Lead Plastic Small Outline (SN) – Narrow, 150 mil (SOIC 45° c β Dimension Limits Number of Pins Pitch Overall Height Molded Package Thickness Standoff § Overall Width Molded Package Width Overall Length Chamfer Distance Foot Length Foot Angle Lead Thickness Lead Width ...
Page 13
... Mold Draft Angle Top *Controlling Parameter Notes: Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010” (0.254mm) per side. JEDEC equivalent: pending Drawing No. C04-113 2003 Microchip Technology Inc. PIC12C508A/C509A/CR509A R D EXPOSED METAL PADS A2 ...
Page 14
... PIC12C508A/C509A/CR509A APPENDIX A: REVISION HISTORY Rev. D Document (6/2003) Under Clarifications/Corrections to the Data Sheet, Item 3, Packaging: correct package data was added. Added Appendix A: Revision History. DS80063D-page 14 2003 Microchip Technology Inc. ...
Page 15
... Serialized Quick Turn Programming (SQTP service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. © 2003, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. Microchip received QS-9000 quality system ...
Page 16
... Korea Microchip Technology Korea 168-1, Youngbo Bldg. 3 Floor Samsung-Dong, Kangnam-Ku Seoul, Korea 135-882 Tel: 82-2-554-7200 Fax: 82-2-558-5934 Singapore Microchip Technology Singapore Pte Ltd. 200 Middle Road #07-02 Prime Centre Singapore, 188980 Tel: 65-6334-8870 Fax: 65-6334-8850 Taiwan Microchip Technology (Barbados) Inc., Taiwan Branch 11F-3, No ...