ATTINY4313-MU Atmel, ATTINY4313-MU Datasheet
ATTINY4313-MU
Specifications of ATTINY4313-MU
Available stocks
Related parts for ATTINY4313-MU
ATTINY4313-MU Summary of contents
Page 1
... Idle Mode • 24 µA at 1.8V and 1MHz – Power-down Mode • 0.1 µA at 1.8V and +25°C ® 8-Bit Microcontroller 8-bit Microcontroller with 2/4K Bytes In-System Programmable Flash ATtiny2313A ATtiny4313 Preliminary Summary Rev. 8246AS–AVR–11/09 ...
Page 2
Pin Configurations Figure 1-1. 1.1 Pin Descriptions 1.1.1 VCC Digital supply voltage. 1.1.2 GND Ground. 1.1.3 Port A (PA2..PA0) Port 3-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port A output ...
Page 3
The Port A pins are tri-stated when a reset condition becomes active, even if the clock is not running. Port A also serves the functions of various special features of the ...
Page 4
Overview The ATtiny2313A/4313 is a low-power CMOS 8-bit microcontroller based on the AVR enhanced RISC architecture. By executing powerful instructions in a single clock cycle, the ATtiny2313A/4313 achieves throughputs approaching 1 MIPS per MHz allowing the system designer to ...
Page 5
... The ATtiny2313A/4313 AVR is supported with a full suite of program and system development tools including: C Compilers, Macro Assemblers, Program Debugger/Simulators, In-Circuit Emu- lators, and Evaluation kits. 2.2 Comparison Between ATtiny2313A and ATtiny4313 The ATtiny2313A and ATtiny4313 differ only in memory sizes. ent memory sizes for the two devices. Table 2-1. Device ATtiny2313A ATtiny4313 8246AS– ...
Page 6
... About 3.1 Resources A comprehensive set of drivers, application notes, data sheets and descriptions on development tools are available for download at http://www.atmel.com/avr. 3.2 Code Examples This documentation contains simple code examples that briefly show how to use various parts of the device. These code examples assume that the part specific header file is included before compilation ...
Page 7
Register Summary Address Name Bit 7 0x3F (0x5F) SREG I 0x3E (0x5E) Reserved – 0x3D (0x5D) SPL SP7 0x3C (0x5C) OCR0B 0x3B (0x5B) GIMSK INT1 0x3A (0x5A) GIFR INTF1 0x39 (0x59) TIMSK TOIE1 0x38 (0x58) TIFR TOV1 0x37 (0x57) ...
Page 8
Notes: 1. For compatibility with future devices, reserved bits should be written to zero if accessed. Reserved I/O memory addresses should never be written. 2. I/O Registers within the address range 0x00 - 0x1F are directly bit-accessible using the SBI ...
Page 9
Instruction Set Summary Mnemonics Operands ARITHMETIC AND LOGIC INSTRUCTIONS ADD Rd, Rr Add two Registers ADC Rd, Rr Add with Carry two Registers ADIW Rdl,K Add Immediate to Word SUB Rd, Rr Subtract two Registers SUBI Rd, K Subtract ...
Page 10
Mnemonics Operands ROR Rd Rotate Right Through Carry ASR Rd Arithmetic Shift Right SWAP Rd Swap Nibbles BSET s Flag Set BCLR s Flag Clear BST Rr, b Bit Store from Register to T BLD Rd, b Bit load from ...
Page 11
... Notes: 1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering information and minimum quantities. 2. Pb-free packaging, complies to the European Directive for Restriction of Hazardous Substances (RoHS directive). Also Halide free and fully Green. ...
Page 12
... Body, Quad Flat No-Lead/Micro Lead Frame Package (MLF) 20M2 20-pad 0.85 mm Body, Very Thin Quad Flat No Lead Package (VQFN) ATtiny2313A/4313 12 (2) Ordering Code Package ATtiny4313-PU ATtiny4313-SU ATtiny4313-MU (4)(5) ATtiny4313-MMH 196. Package Type (1) Operation Range 20P3 20S Industrial 20M1 (-40° ...
Page 13
Packaging Information 7.1 20P3 A SEATING PLANE Notes: 1. This package conforms to JEDEC reference MS-001, Variation AD. 2. Dimensions D and E1 do not include mold Flash or Protrusion. Mold Flash or Protrusion shall not ...
Page 14
ATtiny2313A/4313 14 8246AS–AVR–11/09 ...
Page 15
D 1 Pin TOP VIEW D2 Pin #1 Notch (0. BOTTOM VIEW Reference JEDEC Standard MO-220, Fig. 1 (SAW Singulation) WGGD-5. Note: 2325 Orchard Parkway San Jose, CA 95131 R 8246AS–AVR–11/09 E ...
Page 16
... Pin TOP VIEW Pin #1 Chamfer BOTTOM VIEW Package Drawing Contact: packagedrawings@atmel.com ATtiny2313A/4313 C0.18 (8X 0.3 Ref (4x) K TITLE 20M2, 20-pad 0.85 mm Body, Lead Pitch 0.45 mm, 1.55 x 1.55 mm Exposed Pad, Thermally Enhanced Plastic Very Thin Quad Flat No Lead Package (VQFN) ...
Page 17
... Errata The revision letters in this section refer to the revision of the corresponding ATtiny2313A/4313 device. 8.1 ATtiny2313A 8.1.1 Rev known errata. 8.1.2 Rev. A – C These device revisions were referred to as ATtiny2313/ATtiny2313V. 8.2 ATtiny4313 8.2.1 Rev known errata. 8246AS–AVR–11/09 17 ...
Page 18
... Section 20.6.13 “Reading the Signature Bytes” on page Section 21.2 “DC Characteristics” on page Section 22.1 “Effect of Power Reduction” on page Section 22. “Typical Characteristics” 204 - 227), and added plots for ATtiny4313 (pages Section 4. “Register Summary” on page 7 Section 6. “Ordering Information” on page 2. 34. ...
Page 19
8246AS–AVR–11/09 19 ...
Page 20
... Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT ...