PIC16F690-E/P Microchip Technology, PIC16F690-E/P Datasheet - Page 177

• Manufacturer Part Number: PIC16F690-E/P
• Description: IC PIC MCU FLASH 4KX14 20DIP
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F690-E/P

• Program Memory Type: FLASH
• Program Memory Size: 7KB (4K x 14)
• Package / Case: 20-DIP (0.300", 7.62mm)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 18
• Eeprom Size: 256 x 8
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Processor Series: PIC16F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: I2C/SPI/SSP/EUSART
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 17
• Number Of Timers: 3
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DM163014, DM164120-1, DM163029
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: PIC16F690DM-PCTLHS - BOARD DEMO PICTAIL HUMIDITY SNSRAC162061 - HEADER INTRFC MPLAB ICD2 20PINAC164039 - MODULE SKT PROMATE II 20DIP/SOICDM163029 - BOARD PICDEM FOR MECHATRONICSACICE0203 - MPLABICE 20P 300 MIL ADAPTER
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

12.4.2
The following bits are used to configure the EUSART
for Synchronous slave operation:
• SYNC = 1
• CSRC = 0
• SREN = 0 (for transmit); SREN = 1 (for receive)
• CREN = 0 (for transmit); CREN = 1 (for receive)
• SPEN = 1
Setting the SYNC bit of the TXSTA register configures the
device for synchronous operation. Clearing the CSRC bit
of the TXSTA register configures the device as a slave.
Clearing the SREN and CREN bits of the RCSTA register
ensures that the device is in the Transmit mode,
otherwise the device will be configured to receive. Setting
the SPEN bit of the RCSTA register enables the
EUSART. If the RX/DT or TX/CK pins are shared with an
analog peripheral the analog I/O functions must be
disabled by clearing the corresponding ANSEL bits.
12.4.2.1
The operation of the Synchronous Master and Slave
modes
“Synchronous Master Transmission”), except in the
case of the Sleep mode.
TABLE 12-9:
© 2008 Microchip Technology Inc.
BAUDCTL ABDOVF
INTCON
PIE1
PIR1
RCREG
RCSTA
SPBRG
SPBRGH
TRISB
TXREG
TXSTA
Legend:
Name
are
x = unknown, – = unimplemented read as ‘0’. Shaded cells are not used for Synchronous Slave Transmission.
SYNCHRONOUS SLAVE MODE
EUSART Receive Data Register
EUSART Transmit Data Register
TRISB7
BRG15
CSRC
EUSART Synchronous Slave
Transmit
SPEN
BRG7
Bit 7
GIE
—
—
identical
REGISTERS ASSOCIATED WITH SYNCHRONOUS SLAVE TRANSMISSION
TRISB6
BRG14
RCIDL
BRG6
PEIE
ADIE
ADIF
Bit 6
RX9
TX9
(see
TRISB5
BRG13
SREN
BRG5
TXEN
RCIE
RCIF
Bit 5
T0IE
—
PIC16F631/677/685/687/689/690
Section 12.4.1.3
TRISB4
BRG12
CREN
SCKP
BRG4
SYNC
INTE
Bit 4
TXIE
TXIF
ADDEN
SENDB
BRG16
BRG11
RABIE
SSPIE
SSPIF
BRG3
Bit 3
CCP1IE
CCP1IF
BRG10
BRGH
FERR
BRG2
If two words are written to the TXREG and then the
SLEEP instruction is executed, the following will occur:
1.
2.
3.
4.
5.
12.4.2.2
1.
2.
3.
4.
5.
6.
7.
Bit 2
T0IF
—
The first character will immediately transfer to
the TSR register and transmit.
The second word will remain in TXREG register.
The TXIF bit will not be set.
After the first character has been shifted out of
TSR, the TXREG register will transfer the second
character to the TSR and the TXIF bit will now be
set.
If the PEIE and TXIE bits are set, the interrupt
will wake the device from Sleep and execute the
next instruction. If the GIE bit is also set, the
program will call the Interrupt Service Routine.
Set the SYNC and SPEN bits and clear the
CSRC bit.
Clear the CREN and SREN bits.
If interrupts are desired, set the TXIE bit of the
PIE1 register and the GIE and PEIE bits of the
INTCON register.
If 9-bit transmission is desired, set the TX9 bit.
Enable transmission by setting the TXEN bit.
If 9-bit transmission is selected, insert the Most
Significant bit into the TX9D bit.
Start
Significant 8 bits to the TXREG register.
TMR2IE
TMR2IF
OERR
BRG1
BRG9
TRMT
WUE
Bit 1
INTF
transmission
Synchronous Slave Transmission
Set-up:
TMR1IE
TMR1IF
ABDEN
RABIF
BRG0
BRG8
RX9D
TX9D
Bit 0
by
01-0 0-00
0000 000x
-000 0000
-000 0000
0000 0000
0000 000x
0000 0000
0000 0000
1111 ----
0000 0000
0000 0010
POR, BOR
Value on
writing
DS41262E-page 175
the
01-0 0-00
0000 000x
-000 0000
-000 0000
0000 0000
0000 000x
0000 0000
0000 0000
1111 ----
0000 0000
0000 0010
Value on
all other
Resets
Least