PIC16C712-04I/SO Microchip Technology, PIC16C712-04I/SO Datasheet
PIC16C712-04I/SO
Specifications of PIC16C712-04I/SO
Related parts for PIC16C712-04I/SO
PIC16C712-04I/SO Summary of contents
Page 1
... The problem here will be addressed in future revisions of the PIC16C712/716 silicon. 1. Module: CCP When using the PIC16C712/716 in the Compare or PWM mode, the TCCP bit of the TRISCCP register will not tristate the output on pin RB3, as described in Figure 7-2 of the Device Data Sheet. The TCCP bit of the TRISCCP register has no effect on the output of pin RB3 ...
Page 2
... PIC16C712/716 Assembly Code To Start PWM Once Stopped: PWMrestart bcf STATUS,RP0 ; Select Bank 0 movlw T2CONVAL ; Load T2CON value in ‘w’ register - USER RESPONSIBLE FOR ; SUPPLYING THE CORRECT T2CON VALUE. movwf T2CON ; Initialize T2CON enabling scalers and Timer2 return Code Example 1B: ;*********************************************************************** ...
Page 3
... Move CCPR1H value into TMR2 to cause Reset of RB3 pin return Assembly Code To Start PWM Once Stopped: PWMrestart bcf STATUS,RP0 ; Select Bank 0 movf T2CONSAV,W ; Move T2CONSAV Value to ‘w’ register movwf T2CON ; Restore T2CON register value return 2003 Microchip Technology Inc. PIC16C712/716 DS80072D-page 3 ...
Page 4
... PIC16C712/716 Code Example 2B: ;*********************************************************************** ; Call these routines to turn the CCP Mode off or on and ensure RB3 is a known ; Input or Output value when CCP Mode is off CCPstop - First sets RB3 to an Input or an Output. If RB3 is an Output then it’s state ; is made either High or Low. The CCP is then Disabled. ...
Page 5
... T1CON,TMR1ON bsf T1CON,NOT_T1SYNC return 2003 Microchip Technology Inc. PIC16C712/716 Timer1 synchronization will start, effectively stop- ping Timer1, one Q period after the Synchronous mode is enabled, or one Q period later than would have been realized by simply clearing the TMR1ON bit. One additional count, in excess of ...
Page 6
... PIC16C712/716 Clarifications/Corrections to the Data Sheet: In the Device Data Sheet (DS41106A), the following clarifications and corrections should be noted. 1. The following register and bit names need the following corrections: Page Where 10 Figure 2-3, Address 0Fh 10 Figure 2-3, Address 11h 41 Table 7-2, Address 07h, bit 0 ...
Page 7
... Figure 12-1, page 76, of the Device Data Sheet should show the following valid region of operation: FIGURE 12-5: PIC16C712/716 VOLTAGE-FREQUENCY GRAPH, -40°C ≤ T 6.0 5.5 5.0 4 (Volts) 4.0 3.5 3.0 2.5 2 Note 1: The shaded region indicates the permissible combinations of voltage and frequency. ...
Page 8
... PIC16C712/716 5. Module: Packaging The package information contained in the data sheet is incorrect. Please refer to the following tables for correct package data. 18-Lead Plastic Dual In-line (P) – 300 mil (PDIP β eB Dimension Limits Number of Pins Pitch Top to Seating Plane Molded Package Thickness Base to Seating Plane ...
Page 9
... L .016 .033 .050 φ .009 .011 .012 B .014 .017 .020 α β PIC16C712/716 α A2 MILLIMETERS MIN NOM MAX 18 1.27 2.36 2.50 2.64 2.24 2.31 2.39 0.10 0.20 0.30 10.01 10.34 10.67 7.39 7.49 7.59 11.33 11.53 11.73 0.25 ...
Page 10
... PIC16C712/716 18-Lead Ceramic Dual In-line with Window (JW) – 300 mil (CERDIP Dimension Limits Number of Pins Pitch Top to Seating Plane Ceramic Package Height Standoff Shoulder to Shoulder Width Ceramic Pkg. Width Overall Length Tip to Seating Plane Lead Thickness Upper Lead Width Lower Lead Width Overall Row Spacing § ...
Page 11
... Mold Draft Angle Bottom * Controlling Parameter § Significant Characteristic Notes: Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010” (0.254mm) per side. JEDEC Equivalent: MO-150 Drawing No. C04-072 2003 Microchip Technology Inc. PIC16C712/716 φ Units ...
Page 12
... PIC16C712/716 APPENDIX A: REVISION HISTORY Rev. A Document (6/2000) First revision of this document. Rev. B Document (4/2001) Added issue 1 (CCP), page 1, and issue 2 (Timer1), page 5. Rev. C Document (1/2002) Under Clarifications/Corrections to the Data Sheet, Item 5 (SSOP), on page 8 was added. Rev. D Document (3/2003) Under Clarifications/Corrections to the Data Sheet, Item 5, Packaging: correct package data was added ...
Page 13
... MPSIM, PICC, PICkit, PICDEM, PICDEM.net, PowerCal, PowerInfo, PowerMate, PowerTool, rfLAB, rfPIC, Select Mode, SmartSensor, SmartShunt, SmartTel and Total Endurance are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. Serialized Quick Turn Programming (SQTP service mark of Microchip Technology Incorporated in the U.S.A. ...
Page 14
... Korea Microchip Technology Korea 168-1, Youngbo Bldg. 3 Floor Samsung-Dong, Kangnam-Ku Seoul, Korea 135-882 Tel: 82-2-554-7200 Fax: 82-2-558-5934 Singapore Microchip Technology Singapore Pte Ltd. 200 Middle Road #07-02 Prime Centre Singapore, 188980 Tel: 65-6334-8870 Fax: 65-6334-8850 Taiwan Microchip Technology (Barbados) Inc., Taiwan Branch 11F-3, No ...