PIC16LF72-I/SS Microchip Technology, PIC16LF72-I/SS Datasheet - Page 14
![IC PIC MCU FLASH 2KX14 28SSOP](/photos/6/81/68119/150-28-ssop_sml.jpg)
PIC16LF72-I/SS
Manufacturer Part Number
PIC16LF72-I/SS
Description
IC PIC MCU FLASH 2KX14 28SSOP
Manufacturer
Microchip Technology
Series
PIC® 16Fr
Datasheets
1.PIC16LF627A-IP.pdf
(8 pages)
2.PIC16F818-ISO.pdf
(6 pages)
3.PIC16F72-ISO.pdf
(136 pages)
4.PIC16F72-ISO.pdf
(136 pages)
Specifications of PIC16LF72-I/SS
Core Size
8-Bit
Program Memory Size
3.5KB (2K x 14)
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Core Processor
PIC
Speed
20MHz
Connectivity
I²C, SPI
Number Of I /o
22
Program Memory Type
FLASH
Ram Size
128 x 8
Voltage - Supply (vcc/vdd)
2 V ~ 5.5 V
Data Converters
A/D 5x8b
Oscillator Type
External
Operating Temperature
-40°C ~ 85°C
Package / Case
28-SSOP
Controller Family/series
PIC16LF
No. Of I/o's
22
Ram Memory Size
128Byte
Cpu Speed
16MHz
No. Of Timers
3
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC16LF72-I/SS
Manufacturer:
Microchi
Quantity:
92 666
Part Number:
PIC16LF72-I/SS
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
PIC16F72
2.2.2.1
The STATUS register, shown in Register 2-1, contains
the arithmetic status of the ALU, the RESET status and
the bank select bits for data memory.
The STATUS register can be the destination for any
instruction, as with any other register. If the STATUS
register is the destination for an instruction that affects
the Z, DC or C bits, then the write to these three bits is
disabled. These bits are set or cleared according to the
device logic. Furthermore, the TO and PD bits are not
writable. Therefore, the result of an instruction with the
STATUS register as destination may be different than
intended.
REGISTER 2-1:
DS39597B-page 12
bit 7
bit 6-5
bit 4
bit 3
bit 2
bit 1
bit 0
STATUS Register
STATUS REGISTER (ADDRESS 03h, 83h, 103h, 183h)
bit 7
IRP: Register Bank Select bit (used for indirect addressing)
1 = Bank 2, 3 (100h - 1FFh)
0 = Bank 0, 1 (00h - FFh)
RP<1:0>: Register Bank Select bits (used for direct addressing)
11 = Bank 3 (180h - 1FFh)
10 = Bank 2 (100h - 17Fh)
01 = Bank 1 (80h - FFh)
00 = Bank 0 (00h - 7Fh)
Each bank is 128 bytes
TO: Time-out bit
1 = After power-up, CLRWDT instruction, or SLEEP instruction
0 = A WDT time-out occurred
PD: Power-down bit
1 = After power-up or by the CLRWDT instruction
0 = By execution of the SLEEP instruction
Z: Zero bit
1 = The result of an arithmetic or logic operation is zero
0 = The result of an arithmetic or logic operation is not zero
DC: Digit carry/borrow bit (ADDWF, ADDLW, SUBLW and SUBWF instructions)
1 = A carry-out from the 4th low order bit of the result occurred
0 = No carry-out from the 4th low order bit of the result
C: Carry/borrow bit (ADDWF, ADDLW, SUBLW and SUBWF instructions)
1 = A carry-out from the Most Significant bit of the result occurred
0 = No carry-out from the Most Significant bit of the result occurred
Legend:
R = Readable bit
- n = Value at POR
R/W-0
Note 1: For borrow, the polarity is reversed. A subtraction is executed by adding the two’s
IRP
2: For rotate (RRF, RLF) instructions, this bit is loaded with either the high or low order
complement of the second operand.
bit of the source register.
R/W-0
RP1
R/W-0
RP0
W = Writable bit
‘1’ = Bit is set
For example, CLRF STATUS will clear the upper three
bits and set the Z bit. This leaves the STATUS register
as ‘000u u1uu’ (where u = unchanged).
It is recommended, therefore, that only BCF, BSF,
SWAPF and MOVWF instructions are used to alter the
STATUS register, because these instructions do not
affect the Z, C or DC bits from the STATUS register. For
other instructions, not affecting any status bits, see
Section 12.0, Instruction Set Summary.
R-1
TO
Note 1: The C and DC bits operate as a borrow
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
and digit borrow bit, respectively, in sub-
traction. See the SUBLW and SUBWF
instructions for examples.
R-1
PD
R/W-x
2002 Microchip Technology Inc.
Z
(1,2)
x = Bit is unknown
(1)
R/W-x
DC
R/W-x
C
bit 0