ATTINY461A-SU Atmel, ATTINY461A-SU Datasheet
![IC MCU AVR 4K FLASH 20MHZ 20SOIC](/photos/6/80/68042/453-20-soic_sml.jpg)
ATTINY461A-SU
Specifications of ATTINY461A-SU
Available stocks
Related parts for ATTINY461A-SU
ATTINY461A-SU Summary of contents
Page 1
... MHz @ 2.7 – 5.5V – 0 – 20 MHz @ 4.5 – 5.5V • Power Consumption at 1MHz, 1.8V, 25°C – Active: 200 µA – Power-Down Mode: 0.1 µA ® 8-Bit Microcontroller 8-bit Microcontroller with 2/4/8K Bytes In-System Programmable Flash ATtiny261A ATtiny461A ATtiny861A Preliminary 8197B–AVR–01/10 ...
Page 2
Pin Configurations Figure 1-1. Pinout ATtiny261A/461A/861A (MOSI/DI/SDA/OC1A/PCINT8) PB0 (MISO/DO/OC1A/PCINT9) PB1 (SCK/USCK/SCL/OC1B/PCINT10) PB2 (ADC7/OC1D/CLKI/XTAL1/PCINT12) PB4 (ADC8/OC1D/CLKO/XTAL2/PCINT13) PB5 (ADC9/INT0/T0/PCINT14) PB6 (ADC10/RESET/PCINT15) PB7 (OC1B/PCINT11) PB3 (ADC7/OC1D/CLKI/XTAL1/PCINT12) PB4 (ADC8/OC1D/CLKO/XTAL2/PCINT13) PB5 Note: To ensure mechanical stability the center pad underneath the QFN/MLF package should ...
Page 3
Pin Descriptions 1.1.1 VCC Supply voltage. 1.1.2 GND Ground. 1.1.3 AVCC Analog supply voltage. This is the supply voltage pin for the Analog-to-digital Converter (ADC), the analog comparator, the Brown-Out Detector (BOD), the internal voltage reference and Port A. ...
Page 4
Overview ATtiny261A/461A/861A are low-power CMOS 8-bit microcontrollers based on the AVR enhanced RISC architecture. By executing powerful instructions in a single clock cycle, the devices achieve throughputs approaching 1 MIPS per MHz allowing the system designer to opti- mize ...
Page 5
... The device is manufactured using Atmel’s high density non-volatile memory technology. The On-chip ISP Flash allows the Program memory to be re-programmed In-System through an SPI serial interface conventional non-volatile memory programmer On-chip boot code running on the AVR core ...
Page 6
... General Information 3.1 Resources A comprehensive set of drivers, application notes, data sheets and descriptions on development tools are available for download at http://www.atmel.com/avr. 3.2 Code Examples This documentation contains simple code examples that briefly show how to use various parts of the device. These code examples assume that the part specific header file is included before compilation ...
Page 7
CPU Core This section discusses the AVR core architecture in general. The main function of the CPU core is to ensure correct program execution. The CPU must therefore be able to access memories, perform calculations, control peripherals, and handle ...
Page 8
The fast-access Register File contains 32 x 8-bit general purpose working registers with a single clock cycle access time. This allows single-cycle Arithmetic Logic Unit (ALU) operation typ- ical ALU operation, two operands are output from the Register ...
Page 9
SREG – AVR Status Register Bit 0x3F (0x5F) Read/Write Initial Value • Bit 7 – I: Global Interrupt Enable The Global Interrupt Enable bit must be set for the interrupts to be enabled. The individual inter- rupt enable control ...
Page 10
General Purpose Register File The Register File is optimized for the AVR Enhanced RISC instruction set. In order to achieve the required performance and flexibility, the following input/output schemes are supported by the Register File: • One 8-bit output ...
Page 11
Figure 4-3. X-register Y-register Z-register In different addressing modes these address registers function as automatic increment and automatic decrement (see the instruction set reference for details). 4.5 Stack Pointer The Stack is mainly used for storing temporary data, local variables ...
Page 12
SPH and SPL — Stack Pointer Register Bit 0x3E (0x5E) 0x3D (0x5D) Read/Write Initial Value 4.6 Instruction Execution Timing This section describes the general access timing concepts for instruction execution. The AVR CPU is driven by the CPU clock ...
Page 13
Reset and Interrupt Handling The AVR provides several different interrupt sources. These interrupts and the separate Reset Vector each have a separate Program Vector in the Program memory space. All interrupts are assigned individual enable bits which must be ...
Page 14
Assembly Code Example in r16, SREG cli sbi EECR, EEMPE sbi EECR, EEPE out SREG, r16 C Code Example char cSREG; cSREG = SREG; /* store SREG value */ /* disable interrupts during timed sequence */ _CLI(); EECR |= (1<<EEMPE); ...
Page 15
Memories This section describes the different memories of the ATtiny261A/461A/861A. The AVR architec- ture has two main memory spaces, the Data memory and the Program memory space. In addition, the ATtiny261A/461A/861A features an EEPROM Memory for data storage. All ...
Page 16
When using register indirect addressing modes with automatic pre-decrement and post-incre- ment, the address registers X, Y, and Z are decremented or incremented. The 32 general purpose working registers, 64 I/O Registers, and the 128/256/512 bytes of inter- nal data ...
Page 17
EEPROM Read/Write Access The EEPROM Access Registers are accessible in the I/O space. The write access times for the EEPROM are given in tion, however, lets the user software detect when the next byte can be written. If the ...
Page 18
The calibrated Oscillator is used to time the EEPROM accesses. Make sure the Oscillator fre- quency is within the requirements described in page 32. 5.3.6 Program Examples The following code examples show one assembly and one C function for erase, ...
Page 19
The next code examples show assembly and C functions for reading the EEPROM. The exam- ples assume that interrupts are controlled so that no interrupts will occur during execution of these functions. Assembly Code Example EEPROM_read: C Code Example unsigned ...
Page 20
... Bit 0 – EEAR8: EEPROM Address This is the most significant EEPROM address bit of ATtiny861A. In devices with less EEPROM, i.e. ATtiny261A/ATtiny461A, this bit is reserved and will always read zero. The initial value of the EEPROM Address Register (EEAR) is undefined and a proper value must therefore be written before the EEPROM is accessed ...
Page 21
... Initial Value • Bit 7 – EEAR7: EEPROM Address This is the most significant EEPROM address bit of ATtiny461A. In devices with less EEPROM, i.e. ATtiny261A, this bit is reserved and will always read zero. The initial value of the EEPROM Address Register (EEAR) is undefined and a proper value must therefore be written before the EEPROM is accessed. • ...
Page 22
Erase and Write operations in two different operations. The Programming times for the different modes are shown in Table 5-1. EEPM1 When EEPE is set, ...
Page 23
GPIOR1 – General Purpose I/O Register 1 Bit 0x0B (0x2B) Read/Write Initial Value 5.5.7 GPIOR0 – General Purpose I/O Register 0 Bit 0x0A (0x2A) Read/Write Initial Value 8197B–AVR–01/ MSB R/W R/W R/W R ...
Page 24
Clock System Figure 6-1 be active at a given time. In order to reduce power consumption, the clocks to modules not being used can be halted by using different sleep modes, as described in Sleep Modes” on page Figure ...
Page 25
Flash Clock – clk FLASH The Flash clock controls operation of the Flash interface. The Flash clock is usually active simul- taneously with the CPU clock. 6.1.4 ADC Clock – clk ADC The ADC is provided with a dedicated ...
Page 26
The watchdog oscillator is used for timing this real-time part of the start-up time. The number of WD oscillator cycles used for each time-out is shown in Table 6-2. 6.2.1 External Clock To drive the device from ...
Page 27
The fast peripheral clock, clk prescaled version of the PLL output, clk a detailed illustration on the PLL clock system. Figure 6-3. XTAL1 XTAL2 The internal PLL is enabled when CKSEL fuse bits are programmed to ‘0001’and the PLLE bit ...
Page 28
When the PLL output is selected as clock source, the start-up times are determined by SUT fuse bits as shown in Table 6-5. SUT1 6.2.3 Calibrated Internal 8 MHz Oscillator By default, the Internal Oscillator provides ...
Page 29
It is possible to reach a higher accuracy than factory calibration by changing the OSCCAL regis- ter from software. See this calibration is shown as User calibration in When this oscillator is used as device clock, the Watchdog Oscillator will ...
Page 30
Crystal Oscillator / Ceramic Resonator XTAL1 and XTAL2 are input and output, respectively inverting amplifier which can be con- figured for use as an On-chip Oscillator, as shown in ceramic resonator may be used. Figure 6-4. C1 ...
Page 31
Table 6-12. CKSEL0 Notes: 6.2.7 Default Clock Source The device is shipped with CKSEL = “0010”, SUT = “10”, and CKDIV8 programmed. The default clock source setting is therefore the Internal Oscillator running at 8 ...
Page 32
From the time the CLKPS values are written, it takes between and T1 + 2*T2 before the new clock frequency is active. In this interval, two active clock edges are produced. Here the previous clock ...
Page 33
Bits 3:0 – CLKPS3:0: Clock Prescaler Select Bits These bits define the division factor between the selected clock source and the internal system clock. These bits can be written run-time to vary the clock frequency to ...
Page 34
Power Management and Sleep Modes The high performance and industry leading code efficiency makes the AVR microcontrollers an ideal choise for low power applications. In addition, sleep modes enable the application to shut down unused modules in the MCU, ...
Page 35
Idle mode enables the MCU to wake up from external triggered interrupts as well as internal ones like the Timer Overflow. If wake-up from the Analog Comparator interrupt is not required, the Analog Comparator can be powered down by setting ...
Page 36
Power Reduction Register The Power Reduction Register (PRR), see vides a method to stop the clock to individual peripherals to reduce power consumption. The current state of the peripheral is frozen and the I/O registers can not be read ...
Page 37
Watchdog Timer If the Watchdog Timer is not needed in the application, this module should be turned off. If the Watchdog Timer is enabled, it will be enabled in all sleep modes, and hence, always consume power. In the ...
Page 38
These bits select between the three available sleep modes as shown in Table 7-2. SM1 • Bit 2 – BODSE: BOD Sleep Enable The BODSE bit enables setting of BODS control bit, as explained on BODS bit description. BOD disable ...
Page 39
System Control and Reset 8.1 Resetting the AVR During reset, all I/O Registers are set to their initial values, and the program starts execution from the Reset Vector. The instruction placed at the Reset Vector must be a RJMP ...
Page 40
Reset Sources The ATtiny261A/461A/861A has four sources of reset: • Power-on Reset. The MCU is reset when the supply voltage is below the Power-on Reset threshold (V • External Reset. The MCU is reset when a low level is ...
Page 41
External Reset An External Reset is generated by a low level on the RESET pin if enabled. Reset pulses longer than the minimum pulse width (see ate a reset, even if the clock is not running. Shorter pulses are ...
Page 42
Watchdog Reset When the Watchdog times out, it will generate a short reset pulse of one CK cycle duration. On the falling edge of this pulse, the delay timer starts counting the Time-out period t “Watchdog Timer” on page ...
Page 43
The Wathdog Timer can also be configured to generate an interrupt instead of a reset. This can be very helpful when using the Watchdog to wake-up from Power-down. To prevent unintentional disabling of the Watchdog or unintentional change of time-out ...
Page 44
In the same operation, write a logical one to WDCE and WDE. Even though the WDE always is set, the WDE must be written to one to start the timed sequence. 2. Within the next four clock cycles, in ...
Page 45
Register Description 8.5.1 MCUSR – MCU Status Register The MCU Status Register provides information on which reset source caused an MCU Reset. Bit 0x34 (0x54) Read/Write Initial Value • Bits 7:4 – Res: Reserved Bits These bits are reserved ...
Page 46
To avoid the Watchdog Reset, WDIE must be set after each interrupt. Table 8-2. WDE • Bit 4 – WDCE: Watchdog Change Enable This bit must be set when ...
Page 47
The WDP3:0 bits determine the Watchdog Timer prescaling when the Watchdog Timer is enabled. The different prescaling values and their corresponding Timeout Periods are shown in Table 8-3. Table 8-3. WDP3 ...
Page 48
Interrupts ...
Page 49
Address Labels Code 0x0000 0x0001 0x0002 0x0003 0x0004 0x0005 0x0006 0x0007 0x0008 0x0009 0x000A 0x000B 0x000C 0x000D 0x000E 0x000F 0x0010 0x0011 0x0012 0x0013 0x0014 0x0015 0x0016 0x0017 0x0018 ... 9.2 External Interrupts The External Interrupts are triggered by the INT0 ...
Page 50
Low Level Interrupt A low level interrupt on INT0 is detected asynchronously. This means that the interrupt source can be used for waking the part also from sleep modes other than Idle (the I/O clock is halted in all ...
Page 51
Control Register (MCUCR) define whether the external interrupt is activated on rising and/or fall- ing edge of the INT1 pin or level sensed. Activity on the pin will cause an interrupt request even if INT1 is configured as an output. ...
Page 52
When a logic change on any PCINT15 pin triggers an interrupt request, PCIF becomes set (one). If the I-bit in SREG and the PCIE bit in GIMSK are set (one), the MCU will jump to the cor- responding Interrupt Vector. ...
Page 53
I/O Ports All AVR ports have true Read-Modify-Write functionality when used as general digital I/O ports. This means that the direction of one port pin can be changed without unintentionally changing the direction of any other pin with the ...
Page 54
Ports as General Digital I/O The ports are bi-directional I/O ports with optional internal pull-ups. tional description of one I/O-port pin, here generically called Pxn. Figure 10-2. General Digital I/O Pxn Note: 10.1.1 Configuring the Pin Each port pin ...
Page 55
The port pins are tri-stated when reset condition becomes active, even if no clocks are running. If PORTxn is written logic one when the pin is configured as an output pin, the port pin ...
Page 56
Figure 10-3. Synchronization when Reading an Externally Applied Pin value SYSTEM CLK INSTRUCTIONS SYNC LATCH Consider the clock period starting shortly after the first falling edge of the system clock. The latch is closed when the clock is low, and ...
Page 57
Digital Input Enable and Sleep Modes As shown in schmitt-trigger. The signal denoted SLEEP in the figure, is set by the MCU Sleep Controller in Power-down mode, Power-save mode, and Standby mode to avoid high power consumption if some ...
Page 58
C Code Example unsigned char i; ... /* Define pull-ups and set outputs high */ /* Define directions for port pins */ PORTB = (1<<PB4)|(1<<PB1)|(1<<PB0); DDRB = (1<<DDB3)|(1<<DDB2)|(1<<DDB1)|(1<<DDB0); /* Insert nop for synchronization*/ _NOP(); /* Read port pins */ i ...
Page 59
Figure 10-5. Alternate Port Functions Pxn PUOExn: PUOVxn: DDOExn: DDOVxn: PVOExn: PVOVxn: DIEOExn: Pxn DIGITAL INPUT-ENABLE OVERRIDE ENABLE DIEOVxn: Pxn DIGITAL INPUT-ENABLE OVERRIDE VALUE SLEEP: PTOExn: Note: 8197B–AVR–01/10 (1) PUOExn PUOVxn 1 0 DDOExn DDOVxn 1 0 PVOExn PVOVxn 1 ...
Page 60
Table 10-2 ure 10-5 in the modules having the alternate function. Table 10-2. Signal Name PUOE PUOV DDOE DDOV PVOE PVOV PTOE DIEOE DIEOV DI AIO The following subsections shortly describe the alternate functions for each port, and relate the ...
Page 61
Alternate Functions of Port A The Port A pins with alternate function are shown in Table 10-3. • Port A, Bit 7- ADC6/AIN0/PCINT7 • ADC6: Analog to Digital Converter, Channel 6 • AIN0: Analog Comparator Input. Configure the port ...
Page 62
Port A, Bit 5 - ADC4/AIN2/PCINT5 • ADC4: Analog to Digital Converter, Channel 4. • AIN2: Analog Comparator Input. Configure the port pin as input with the internal pull-up switched off to avoid the digital port function from interfering ...
Page 63
Table 10-4 shown in Table 10-4. Signal Name PUOE PUOV DDOE DDOV PVOE PVOV PTOE DIEOE DIEOV DI AIO Table 10-5. Signal Name PUOE PUOV DDOE DDOV PVOE PVOV PTOE DIEOE DIEOV DI AIO 8197B–AVR–01/10 and Table 10-5 relate the ...
Page 64
Alternate Functions of Port B The Port B pins with alternate function are shown in Table 10-6. • Port B, Bit 7 - RESET/ dW/ ADC10/ PCINT15 • RESET, Reset pin: When the RSTDISBL Fuse is programmed, this pin ...
Page 65
ADC10: ADC input Channel 10. Note that ADC input channel 10 uses analog power. • PCINT15: Pin Change Interrupt source 15. • Port B, Bit 6 - ADC9/ T0/ INT0/ PCINT14 • ADC9: ADC input Channel 9. Note that ...
Page 66
DO: Three-wire mode Universal Serial Interface Data output. Three-wire mode Data output overrides PORTB1 value and it is driven to the port when data direction bit DDB1 is set (one). PORTB1 still enables the pull-up, if the direction is ...
Page 67
Table 10-8. Signal Name PUOE PUOV DDOE DDOV PVOE PVOV PTOE DIEOE DIEOV DI AIO Note: 10.3 Register Description 10.3.1 MCUCR – MCU Control Register Bit 0x35 (0x55) Read/Write Initial Value • Bit 6 – PUD: Pull-up Disable When this ...
Page 68
PINA – Port A Input Pins Address Bit 0x19 (0x39) Read/Write Initial Value 10.3.5 PORTB – Port B Data Register Bit 0x18 (0x38) Read/Write Initial Value 10.3.6 DDRB – Port B Data Direction Register Bit 0x17 (0x37) Read/Write Initial ...
Page 69
Timer/Counter0 11.1 Features • Clear Timer on Compare Match (Auto Reload) • One Input Capture unit • Four Independent Interrupt Sources (TOV0, OCF0A, OCF0B, ICF0) • 8-bit Mode with Two Independent Output Compare Units • 16-bit Mode with One ...
Page 70
Timer Interrupt Flag Register (TIFR). All interrupts are individually masked with the Timer Interrupt Mask Register (TIMSK). TIFR and TIMSK are not shown in the figure. In 16-bit mode one more 8-bit register is available, the Timer/Counter0 ...
Page 71
Figure 11-2. Prescaler for Timer/Counter0 clk I/O PSR0 T0 Note: The prescaled clock has a frequency of f Table 11-4 on page 83 11.3.1.1 Prescaler Reset The prescaler is free running, i.e. it operates independently of the Clock Select logic ...
Page 72
Figure 11-3. T0 Pin Sampling Tn clk I/O The synchronization and edge detector logic introduces a delay of 2.5 to 3.5 system clock cycles from an edge has been applied to the T0 pin to the counter is updated. Enabling ...
Page 73
Clock Select bits (CS02:0). When no clock source is selected (CS02 the timer is stopped. However, the TCNT0 value can be accessed by the CPU, regardless of whether clk counter clear or ...
Page 74
TCNT0 value is copied into Input Capture Register. If enabled (TICIE0=1), the Input Capture Flag generates an Input Capture interrupt. The ICF0 flag is auto- matically cleared when the interrupt is executed. Alternatively the ...
Page 75
OCF0B, but in 16-bit mode the match can set only the Output Compare Flag OCF0A as there is only one Output Compare Unit. If the corresponding interrupt is enabled, the Output Compare Flag generates an Output Compare interrupt. The Output ...
Page 76
The Overflow Flag (TOV0) is set in the same timer clock cycle as when TCNT0L becomes zero. The TOV0 Flag in this case behaves like a ninth bit, except that it is only set, not cleared. How- ever, combined with ...
Page 77
Input Capture Mode The Timer/Counter0 can also be used in an 8-bit Input Capture mode, see 75 for bit settings. For full description, see the section 11.7.5 16-bit Input Capture Mode The Timer/Counter0 can also be used in ...
Page 78
Figure 11-9. Timer/Counter Timing Diagram, Setting of OCF0x, with Prescaler (f clk I/O clk Tn (clk /8) I/O TCNTn OCRnx OCFnx Figure 11-10 Figure 11-10. Timer/Counter Timing Diagram, CTC mode, with Prescaler (f clk PCK clk Tn (clk /8) PCK ...
Page 79
The following code examples show how to access the 16-bit timer registers assuming that no interrupts updates the temporary register. The same principle can be used directly for accessing the OCR0A/B registers. Assembly Code Example C Code Example unsigned int ...
Page 80
The following code examples show how atomic read of the TCNT0 register contents. Reading any of the OCR0 register can be done by using the same principle. Assembly Code Example TIM0_ReadTCNT0: ; Save global interrupt flag in ...
Page 81
The following code examples show how atomic write of the TCNT0H/L register con- tents. Writing any of the OCR0A/B registers can be done by using the same principle. Assembly Code Example TIM0_WriteTCNT0: C Code Example void TIM0_WriteTCNT0( ...
Page 82
Register Description 11.10.1 TCCR0A – Timer/Counter0 Control Register A Bit 0x15 (0x35) Read/Write Initial Value • Bit 7– TCW0: Timer/Counter0 Width When this bit is written to one 16-bit mode is selected as described Timer/Counter0 width is set to ...
Page 83
TCCR0B – Timer/Counter0 Control Register B Bit 0x33 (0x53) Read/Write Initial Value • Bit 4 – TSM: Timer/Counter Synchronization Mode Writing the TSM bit to one activates the Timer/Counter Synchronization mode. In this mode, the value that is written ...
Page 84
TCNT0H – Timer/Counter0 Register High Byte Bit 0x14 (0x34) Read/Write Initial Value When 16-bit mode is selected (the TCW0 bit is set to one) the Timer/Counter Register TCNT0H combined to the Timer/Counter Register TCNT0L gives direct access, both for ...
Page 85
Compare Match in Timer/Counter0 occurs, i.e., when the OCF0A bit is set in the Timer/Counter 0 Interrupt Flag Register – TIFR0. • Bit 3 – OCIE0B: Timer/Counter Output Compare Match B Interrupt Enable When the OCIE0B bit is ...
Page 86
Bit 1 – TOV0: Timer/Counter0 Overflow Flag The bit TOV0 is set when an overflow occurs in Timer/Counter0. TOV0 is cleared by hardware when executing the corresponding interrupt handling vector. Alternatively, TOV0 is cleared by writing a logic one ...
Page 87
Timer/Counter1 12.1 Features • 8/10-Bit Accuracy • Three Independent Output Compare Units • Clear Timer on Compare Match (Auto Reload) • Glitch Free, Phase and Frequency Correct Pulse Width Modulator (PWM) • Variable PWM Period • High Speed Asynchronous ...
Page 88
For actual placement of the I/O pins, refer to device-specific I/O register and bit locations are listed in the 12.2.1 Speed The maximum speed of the Timer/Counter1 is 64 MHz. However supply voltage below 2.7 volts is used, ...
Page 89
The read back values are delayed for the Timer/Counter1 (TCNT1) register, Timer/Counter1 High Byte Register (TC1H) and flags (OCF1A, OCF1B, OCF1D and TOV1), because of the input and output synchronization. The system clock frequency ...
Page 90
The definitions in document. Table 12-1. Constant BOTTOM MAX TOP 12.3 Clock Sources The Timer/Counter is clocked internally, either from CK or PCK. See bits CSxx in page 114 12.3.1 Prescaler Figure 12-3 nous clocking ...
Page 91
Prescaler Reset Setting the PSR1 bit in TCCR1B register resets the prescaler possible to use the Prescaler Reset for synchronizing the Timer/Counter to program execution. 12.3.1.2 Prescaler Initialization for Asynchronous Mode To change Timer/Counter1 to the asynchronous ...
Page 92
Counter Initialization for Asynchronous Mode To set Timer/Counter1 to asynchronous mode follow the procedure below: 1. Enable PLL. 2. Wait 100 µs for PLL to stabilize. 3. Poll the PLOCK bit until it is set. 4. Set the PCKE ...
Page 93
PWM pulses, thereby making the output glitch-free. See During the time between the write and the update operation, a read from OCR1A, OCR1B, OCR1C or OCR1D will read the contents of the temporary location. This means that the most ...
Page 94
Dead Time Generator The Dead Time Generator is provided for the Timer/Counter1 PWM output pairs to allow driving external power control switches safely. The Dead Time Generator is a separate block that can be used to insert dead times ...
Page 95
The outputs OC1x and OC1x are inverted, if the PWM Inversion Mode bit PWM1X is set. This will also cause both outputs to be high during the dead time. The length of the counting period is user adjustable by ...
Page 96
Figure 12-10. Compare Match Output Unit, Schematic clk I/O The general I/O port function is overridden by the Output Compare (OC1x / OC1x) from the Dead Time Generator if either of the COM1x1:0 bits are set. However, the OC1x pin ...
Page 97
The design of the Output Compare Pin Configuration logic allows initialization of the OC1x state before the output is enabled. Note that some COM1x1:0 bit settings are reserved for certain modes of operation. For Output Compare Pin Configurations refer to ...
Page 98
The counter value (TCNT1) that is shown as a histogram in counter value matches the TOP value. The counter is then cleared at the following clock cycle The diagram includes the Waveform Output (OCW1x) in toggle Compare Mode. The small ...
Page 99
DAC applications. High frequency allows physically small sized external components (coils, capacitors), and therefore reduces total system cost. The timing diagram for the fast PWM mode is shown in mented until the counter value matches the TOP value. The counter ...
Page 100
COM1x1:0 bits.) A frequency (with 50% duty cycle) waveform output in fast PWM mode can be achieved by set- ting the Waveform Output ...
Page 101
Figure 12-13. Phase and Frequency Correct PWM Mode, Timing Diagram TCNTn OCWnx (COMnx = 2) OCWnx (COMnx = 3) Period The Timer/Counter Overflow Flag (TOV1) is set each time the counter reaches BOTTOM. The Interrupt Flag can be used to ...
Page 102
The configurations of the Output Compare Pins are described in Table 12-4. COM1x1 12.8.4 PWM6 Mode The PWM6 Mode (PWM1A = 1, WGM11:10 ...
Page 103
Figure 12-14. PWM6 Mode, Single-slope Operation, Timing Diagram TCNT1 OCW1A OC1OE0 OC1A Pin OC1OE1 OC1A Pin OC1OE2 OC1B Pin OC1OE3 OC1B Pin OC1OE4 OC1D Pin OC1OE5 OC1D Pin The general I/O port function is overridden by the Output Compare value ...
Page 104
Table 12-7. COM1D1 12.9 Timer/Counter Timing Diagrams The Timer/Counter is a synchronous design and the timer clock (clk clock enable signal in the following figures. The figures include information on when Interrupt Flags are set. Figure ...
Page 105
Figure 12-17. Timer/Counter Timing Diagram, Setting of OCF1x, with Prescaler (f clk PCK clk Tn (clk /8) PCK TCNTn OCRnx OCFnx Figure 12-18 Figure 12-18. Timer/Counter Timing Diagram, with Prescaler (f clk PCK clk Tn (clk /8) PCK TCNTn TOVn ...
Page 106
The Fault Protection Enable (FPEN1) is automatically cleared at the same system clock as the COM1nx bits are cleared. If the Fault Protection Interrupt Enable bit (FPIE1) is set, a Fault Protection interrupt is generated and the FPEN1 bit ...
Page 107
Code Examples The following code examples show how to access the 10-bit timer registers assuming that no interrupts updates the TC1H register. The same principle can be used directly for accessing the OCR1A/B/C/D registers. Assembly Code Example C Code ...
Page 108
The following code examples show how atomic read of the TCNT1 register contents. Reading any of the OCR1A/B/C/D registers can be done by using the same principle. Assembly Code Example TIM1_ReadTCNT1: ; Save global interrupt flag in ...
Page 109
The following code examples show how atomic write of the TCNT1 register contents. Writing any of the OCR1A/B/C/D registers can be done by using the same principle. Assembly Code Example TIM1_WriteTCNT1: C Code Example void TIM1_WriteTCNT1( unsigned ...
Page 110
Register Description 12.12.1 TCCR1A – Timer/Counter1 Control Register A Bit 0x30 (0x50) Read/Write Initial value • Bits 7,6 - COM1A1, COM1A0: Comparator A Output Mode, Bits 1 and 0 These bits control the behaviour of the Waveform Output (OCW1A) ...
Page 111
Table 12-10 are set to Phase and Frequency Correct PWM Mode. Table 12-10. Compare Output Mode, Phase and Frequency Correct PWM Mode COM1A1 Table 12-11 are set to single-slope PWM6 Mode. In the PWM6 Mode the ...
Page 112
Bits 5,4 - COM1B1, COM1B0: Comparator B Output Mode, Bits 1 and 0 These bits control the behaviour of the Waveform Output (OCW1B) and the connection of the Output Compare pin (OC1B). If one or both of the COM1B1:0 ...
Page 113
COM1B1S and COM1B0S in TCCR1C will show here. See Register C” on page • Bit 3 - FOC1A: Force Output Compare Match 1A The FOC1A bit is only active when the PWM1A bit specify a non-PWM mode. Writing a logical ...
Page 114
The dedicated Dead Time prescaler in front of the Dead Time Generator can divide the Timer/Counter1 clock (PCK or CK providing a large range of dead times that can be generated. The Dead Time ...
Page 115
TCCR1C – Timer/Counter1 Control Register C Bit 0x27 (0x47) Read/Write Initial value • Bits 7,6 - COM1A1S, COM1A0S: Comparator A Output Mode, Shadow Bits 1 and 0 These are shadow bits of COM1A1 and COM1A0 in TCCR1A. Writing to ...
Page 116
Table 12-20 set to Phase and Frequency Correct PWM Mode. Table 12-20. Compare Output Mode, Phase and Frequency Correct PWM Mode COM1D1 • Bit 1 - FOC1D: Force Output Compare Match 1D The FOC1D bit is ...
Page 117
Bit 3 - FPAC1: Fault Protection Analog Comparator Enable When written logic one, this bit enables the Fault Protection function in Timer/Counter1 to be triggered by the Analog Comparator. The comparator output is in this case directly connected to ...
Page 118
Output Compare Override Enable Bit is cleared. Override Enable Bits and their corresponding Output Compare pins. Table 12-22. Output Compare Override Enable Bits vs. Output Compare Pins Output CompareOverride Enable Bit OC1OE0 OC1OE1 OC1OE2 OC1OE3 OC1OE4 OC1OE5 12.12.6 PLLCSR ...
Page 119
TCNT1 – Timer/Counter1 Bit 0x2E (0x4E) Read/Write Initial value This 8-bit register contains the value of Timer/Counter1. The Timer/Counter1 is realized as a 10-bit up/down counter with read and write access. Due to synchronization of the CPU, Timer/Counter1 data ...
Page 120
OCR1B – Timer/Counter1 Output Compare Register B Bit 0x2C (0x4C) Read/Write Initial value The output compare register 8-bit read/write register. The Timer/Counter Output Compare Register B contains data to be continuously compared with Timer/Counter1. Actions on ...
Page 121
Note that, if 10-bit accuracy is used special procedures must be followed when accessing the internal 10-bit Output Compare Registers via the 8-bit AVR data bus. These procedures are described in section 12.12.13 TIMSK – Timer/Counter1 Interrupt Mask Register Bit ...
Page 122
Alternatively, OCF1A is cleared, after synchroniza- tion clock cycle, by writing a logic one to the flag. When the I-bit in SREG, OCIE1A, and OCF1A are set (one), the Timer/Counter1 A compare match interrupt is ...
Page 123
USI – Universal Serial Interface 13.1 Features • Two-wire Synchronous Data Transfer (Master or Slave) • Three-wire Synchronous Data Transfer (Master or Slave) • Data Received Interrupt • Wakeup from Idle Mode • In Two-wire Mode: Wake-up from All ...
Page 124
The 4-bit counter can be both read and written via the data bus, and it can generate an overflow interrupt. The data register and the counter are clocked simultaneously by the same clock source, allowing the counter to count the ...
Page 125
Figure 13-3. Three-wire Mode, Timing Diagram CYCLE USCK USCK DO DI The Three-wire mode timing is shown in Figure 13-3. At the top of the figure is a USCK cycle ref- erence. One bit is shifted into the USI Data ...
Page 126
The code is size optimized using only eight instructions (plus return). The code example assumes that the DO and USCK pins have been enabled as outputs in DDRA. The value stored in register r16 prior to the function is called ...
Page 127
SPI Slave Operation Example The following code demonstrates how to use the USI module as a SPI Slave: init: ... SlaveSPITransfer: SlaveSPITransfer_loop: The code is size optimized using only eight instructions (+ ret). The code example assumes that the ...
Page 128
Figure 13-4. Two-wire Mode Operation, Simplified Diagram The data direction is not given by the physical layer. A protocol, like the one used by the TWI- bus, must be implemented to control the data flow. Figure 13-5. Two-wire Mode, Typical ...
Page 129
The master set the first bit to be transferred and releases the SCL line (C). The slave samples the data and shifts it into the USI Data Register at the positive edge of the SCL clock. 4. After eight ...
Page 130
Half-Duplex Asynchronous Data Transfer Using the USI Data Register in three-wire mode it is possible to implement a more compact and higher performance UART than by software, only. 13.4.2 4-Bit Counter The 4-bit counter can be used as a ...
Page 131
USIBR – USI Buffer Register Bit 0x10 (0x30) Read/Write Initial Value The content of the Serial Register is loaded to the USI Buffer Register when the trasfer is com- pleted, and instead of accessing the USI Data Register (the ...
Page 132
The 4-bit counter increments by one for each clock generated either by the external clock edge detector Timer/Counter0 Compare Match software using USICLK or USITC strobe bits. The clock source depends of the setting of the ...
Page 133
Table 13-1. USIWM1 1 1 Note: • Bit 3:2 – USICS1:0: Clock Source Select These bits set the clock source for the USI Data Registerr and counter. The data output latch ensures that the output is changed at the opposite ...
Page 134
Table 13-2. USICS1 • Bit 1 – USICLK: Clock Strobe Writing a one to this bit location strobes the USI Data Register to shift one step and the counter to increment by one, provided that the USICS1:0 ...
Page 135
AC – Analog Comparator The analog comparator compares the input values on the selectable positive pin (AIN0, AIN1 or AIN2) and selectable negative pin (AIN0, AIN1 or AIN2). When the voltage on the positive pin is higher than the ...
Page 136
Table 14-1. ACME ATtiny261A/461A/861A ...
Page 137
Register Description 14.2.1 ACSRA – Analog Comparator Control and Status Register A Bit 0x08 (0x28) Read/Write Initial Value • Bit 7 – ACD: Analog Comparator Disable When this bit is written logic one, the power to the analog comparator ...
Page 138
Bits 1, 0 – ACIS1, ACIS0: Analog Comparator Interrupt Mode Select These bits determine which comparator events that trigger the Analog Comparator interrupt. The different settings are shown in Table 14-2. ACIS1 When changing the ...
Page 139
AREF pin and the digital input from this pin is not needed, this bit should be written logic one to reduce power consumption in the digital input buffer. 14.2.4 DIDR1 – Digital Input Disable Register 1 Bit ...
Page 140
ADC – Analog to Digital Converter 15.1 Features • 10-bit Resolution • 1.0 LSB Integral Non-linearity • ± 2 LSB Absolute Accuracy • 13µs Conversion Time • 15 kSPS at Maximum Resolution • 11 Multiplexed Single Ended Input Channels ...
Page 141
Figure 15-1. Analog to Digital Converter Block Schematic 8-BIT DATA BUS VCC AREF INTERNAL 2.56/1.1V INTERNAL 1.18V AGND ADC10 ADC9 ADC8 ADC7 ADC6 ADC5 ADC4 ADC3 ADC2 ADC1 ADC0 15.3 Operation The ADC converts an analog input voltage to a ...
Page 142
AREF pin to improve noise immunity. The analog input channel and differential gain are selected by writing to the MUX5:0 bits in ADMUX. Any of the 11 ADC input pins ...
Page 143
If another positive edge occurs on the trigger signal during con- version, the edge will be ignored. Note that an Interrupt Flag will be set even if the specific interrupt is disabled or the Global ...
Page 144
The ADC module contains a prescaler, which generates an acceptable ADC clock frequency from any CPU frequency above 100 kHz. The prescaling is set by the ADPS bits in ADCSRA. The prescaler starts counting from the moment the ADC is ...
Page 145
When Auto Triggering is used, the prescaler is reset when the trigger event occurs. See 15-6. This assures a fixed delay from the trigger event to the start of conversion. In this mode, the sample-and-hold takes place two ADC clock ...
Page 146
For a summary of conversion times, see Table 15-1. Condition First conversion Normal conversions Auto Triggered conversions 15.6 Changing Channel or Reference Selection The MUX5:0 and REFS2:0 bits in the ADCSRB and ADMUX registers are single buffered through a temporary ...
Page 147
Since the next conversion has already started automatically, the next result will reflect the previous channel selection. Subsequent conversions will reflect the new channel selection. 15.6.2 ADC Voltage Reference The conversion range of the ADC is defined by the ...
Page 148
Figure 15-8. Analog Input Circuitry The capacitor in and any stray or parasitic capacitance inside the device. The value given is worst case. The ADC is optimized for analog signals with an output impedance of approximately 10 kΩ or less. ...
Page 149
Offset: The deviation of the first transition (0x000 to 0x001) compared to the ideal transition (at 0.5 LSB). Ideal value: 0 LSB. Figure 15-9. Offset Error Output Code • Gain Error: After adjusting for offset, the Gain Error is ...
Page 150
Integral Non-linearity (INL): After adjusting for offset and gain error, the INL is the maximum deviation of an actual transition compared to an ideal transition for any code. Ideal value: 0 LSB. Figure 15-11. Integral Non-linearity (INL) Output Code ...
Page 151
Quantization Error: Due to the quantization of the input voltage into a finite number of codes, a range of input voltages (1 LSB wide) will code to the same value. Always ± 0.5 LSB. • Absolute Accuracy: The maximum ...
Page 152
V and V REF 0x200 (-512d) through 0x000 (+0d) to 0x1FF (+511d). The GAIN is either 1x, 8x, 20x or 32x. However, if the signal is not bipolar by nature (9 bits + sign as the 10th bit), this ...
Page 153
Register Description 15.13.1 ADCSRA – ADC Control and Status Register A Bit 0x06 (0x26) Read/Write Initial Value • Bit 7 – ADEN: ADC Enable Writing this bit to one enables the ADC. By writing it to zero, the ADC ...
Page 154
Table 15-3. ADPS2 15.13.2 ADCL and ADCH – The ADC Data Register 15.13.2.1 ADLAR = 0 Bit 0x05 (0x25) 0x04 (0x24) Read/Write Initial Value 15.13.2.2 ADLAR = 1 Bit 0x05 (0x25) 0x04 (0x24) Read/Write Initial Value When an ADC conversion ...
Page 155
Bit 7:6 – REFS1:REFS0: Voltage Reference Selection Bits These bits together with the REFS2 bit from the ADC Control and Status Register B (ADCSRB) select the voltage reference for the ADC, as shown in Table 15-4. REFS2 X X ...
Page 156
Selecting the single-ended channel ADC11 enables the temperature sensor. Refer to Table 15-5. MUX5:0 000000 000001 000010 000011 000100 000101 000110 000111 001000 001001 001010 001011 001100 001101 001110 001111 010000 010001 010010 010011 010100 ...
Page 157
Table 15-5. MUX5:0 100000 100001 100010 100011 100100 100101 100110 100111 101000 101001 101010 101011 101100 101101 101110 101111 110000 110001 110010 110011 110100 110101 110110 110111 111000 111001 111010 111011 111100 111101 111110 111111 Note: 8197B–AVR–01/10 Input Channel Selections ...
Page 158
If these bits are changed during a conversion, the change will not go into effect until this conver- sion is complete (ADIF in ADCSRA is set). 15.13.4 ADCSRB – ADC Control and Status Register B Bit 0x03 (0x23) Read/Write Initial ...
Page 159
If ADEN in ADCSRA is set, this will start a conversion. Switching to Free Running mode (ADTS[2:0]=0) will not cause a trigger event, even if the ADC Interrupt Flag is set Table 15-6. ADTS2 15.13.5 DIDR0 – Digital ...
Page 160
On-chip Debug System 16.1 Features • Complete Program Flow Control • Emulates All On-chip Functions, Both Digital and Analog , except RESET Pin • Real-time Operation • Symbolic Debugging Support (Both at C and Assembler Source Level, or ...
Page 161
Pull-Up resistor on the dW/(RESET) line must be in the range of 10k to 20 kΩ. However, the pull-up resistor is optional. • Connecting the RESET pin directly to V • Capacitors inserted on the RESET pin must be ...
Page 162
Self-Programming the Flash The device provides a Self-Programming mechanism for downloading and uploading program code by the MCU itself. The Self-Programming can use any available data interface and associ- ated protocol to read code and write (program) that code ...
Page 163
If the EEPROM is written in the middle of an SPM Page Load operation, all data loaded will be lost. 17.3 Performing a Page Write To execute Page Write, set up the address in the Z-pointer, write “00000101” to SPMCSR ...
Page 164
EEPROM Write Prevents Writing to SPMCSR Note that an EEPROM write operation will block all software programming to Flash. Reading the Fuses and Lock bits from software will also be prevented during the EEPROM write operation recommended ...
Page 165
To read the Fuse High Byte (FHB), simply replace the address in the Z-pointer with 0x0003 and repeat the procedure above. If successful, the contents of the destination register are as follows. Bit Rd Refer to To read the Fuse ...
Page 166
Register Description 17.9.1 SPMCSR – Store Program Memory Control and Status Register The Store Program Memory Control and Status Register contains the control bits needed to con- trol the Program memory operations. Bit 0x37 (0x57) Read/Write Initial Value • ...
Page 167
Memory Programming This section describes the different methods for programming ATtiny261A/461A/861A memories. 18.1 Program And Data Memory Lock Bits The device provides two lock bits which can be left unprogrammed (“1”) or can be programmed (“0”) to obtain the ...
Page 168
Fuse Bytes The device has three fuse bytes. functionality of all the fuses and how they are mapped into the fuse bytes. Note that the fuses are read as logical zero, “0”, if they are programmed. Table 18-3. Fuse ...
Page 169
... The three bytes reside in a separate address space. The signature bytes are given in Table 18-6. Table 18-6. Parts ATtiny261A ATtiny461A ATtiny861A 18.4 Calibration Byte The signature area has one byte of calibration data for the internal oscillator. This byte resides in the high byte of address 0x000. During reset, this byte is automatically written into the OSCCAL Register to ensure correct frequency of the calibrated oscillator. 8197B– ...
Page 170
... ATtiny261A ATtiny461A ATtiny861A Table 18-8. Device ATtiny261A ATtiny461A ATtiny861A 18.6 Serial Programming Both the Flash and EEPROM memory arrays can be programmed using the serial SPI bus while RESET is pulled to GND. The serial interface consists of pins SCK, MOSI (input) and MISO (out- put) ...
Page 171
After RESET is set low, the Programming Enable instruction needs to be executed first before program/erase operations can be executed. Table 18-9. Note: When programming the EEPROM, an auto-erase cycle is built into the self-timed programming operation (in the Serial ...
Page 172
Flash write operation completes can result in incorrect programming The EEPROM array is programmed one byte at a time by supplying the address and data together with the appropriate Write instruction. An EEPROM memory location ...
Page 173
... Refer to the correspondig section for Fuse and Lock bits, Calibration and Signature bytes and Page size. 6. Instructions accessing program memory use a word address. This address may be random within the page range. 7. See http://www.atmel.com/avr for Application Notes regarding programming and programmers. If the LSB in RDY/BSY data byte out is ‘1’, a programming operation is still pending. Wait until this bit returns ‘ ...
Page 174
Figure 18-2. Serial Programming Instruction example Load Program Memory Page (High/Low Byte)/ Load EEPROM Memory Page (page access) Byte 1 Byte 2 Byte 3 Adr Adr MSB Bit 15 B 18.7 Parallel Programming ...
Page 175
Figure 18-3. Parallel Programming. Table 18-12. Pin Name Mapping Signal Name in Programming Mode XA1/BS2 PAGEL/BS1 RDY/BSY DATA I/O 8197B–AVR–01/10 WR PB0 XA0 PB1 XA1/BS2 PB2 PAGEL/BS1 PB3 XTAL1/PB4 OE PB5 RDY/BSY PB6 +12 V RESET GND Pin Name I/O ...
Page 176
Table 18-13. Pin Values Used to Enter Programming Mode The XA1/XA0 pins determine the action executed when the XTAL1 pin is given a positive pulse. The bit coding is shown in Table 18-14. XA1 and XA0 Coding XA1 0 0 ...
Page 177
Entering Programming Mode The following algorithm puts the device in parallel programming mode: 1. Apply 4.5 - 5.5V between V 2. Set RESET to “0” and toggle XTAL1 at least six times. 3. Set Prog_enable pins listed in ns. ...
Page 178
Load Command “Write Flash”: a. Set XA1, XA0 to “10”. This enables command loading. b. Set BS1 to “0”. c. Set DATA to “0001 0000”. This is the command for Write Flash. d. Give XTAL1 a positive pulse. This ...
Page 179
Figure 18-4. Addressing the Flash Which is Organized in Pages PROGRAM MEMORY Note: In the figure below, “XX” means don’t care. The numbers in the figure refer to the programming description above. WR Figure 18-5. Flash Programming Waveforms STEP DATA ...
Page 180
The programming algorithm for the EEPROM data memory is as follows (refer to Data loading Load Command “0001 0001” Load Address High Byte (0x00 - 0xFF Load Address Low Byte (0x00 - ...
Page 181
Reading the EEPROM The algorithm for reading the EEPROM memory is as follows (refer to on page 177 1. A: Load Command “0000 0011” Load Address High Byte (0x00 - 0xFF Load Address Low Byte ...
Page 182
Figure 18-7. Programming the FUSES Waveforms DATA XA1/BS2 XA0 PAGEL/BS1 XTAL1 WR RDY/BSY RESET +12V OE 18.7.12 Programming the Lock Bits The algorithm for programming the Lock bits is as follows (refer to page 177 1. A: Load Command “0010 ...
Page 183
Figure 18-8. Mapping Between BS1, BS2 and the Fuse and Lock Bits During Read Fuse Low Byte Extended Fuse Byte Fuse High Byte 18.7.14 Reading the Signature Bytes The algorithm for reading the Signature bytes is as follows (refer to ...
Page 184
Electrical Characteristics 19.1 Absolute Maximum Ratings* Operating Temperature.................................. -55°C to +125°C Storage Temperature ..................................... -65°C to +150°C Voltage on any Pin except RESET with respect to Ground ................................-0. Voltage on RESET with respect to Ground......-0.5V to +13.0V ...
Page 185
Table 19-1. DC Characteristics. T Symbol Parameter Power Supply Current I CC Power-down mode Notes: 1. “Min” means the lowest value where the pin is guaranteed to be read as high. 2. “Max” means the highest value where the pin ...
Page 186
Clock Characteristics 19.4.1 Accuracy of Calibrated Internal Oscillator It is possible to manually calibrate the internal oscillator to be more accurate than default factory calibration. Note that the oscillator frequency depends on temperature and voltage. Voltage and temperature characteristics ...
Page 187
System and Reset Characteristics Table 19-4. Symbol V RST t RST V HYST t BOD Notes: 19.5.1 Enhanced Power-On Reset Table 19-5. Symbol V POR V POA SR ON Note: 19.5.2 Brown-Out Detection ...
Page 188
ADC Characteristics Table 19-7. ADC Characteristics, Single Ended Channels -40°C - 85°C Symbol Parameter Resolution Absolute accuracy (Including INL, DNL, and Quantization, Gain and Offset Errors) Integral Non-Linearity (INL) (Accuracy after Offset and Gain Calibration) Differential Non-linearity ...
Page 189
Serial Programming Characteristics Figure 19-3. Serial Programming Waveforms SERIAL DATA INPUT SERIAL DATA OUTPUT SERIAL CLOCK INPUT Figure 19-4. Serial Programming Timing Table 19-8. Symbol 1/t CLCL t CLCL 1/t CLCL t CLCL t SHSL t SLSH t OVSH ...
Page 190
Parallel Programming Characteristics Figure 19-5. Parallel Programming Timing, Including some General Timing Requirements XTAL1 Data & Contol (DATA, XA0, XA1/BS2, PAGEL/BS1) WR RDY/BSY Figure 19-6. Parallel Programming Timing, Loading Sequence with Timing Requirements LOAD ADDRESS (LOW BYTE) XTAL1 PAGEL/BS1 ...
Page 191
Figure 19-7. Parallel Programming Timing, Reading Sequence (within the Same Page) with Timing Requirements LOAD ADDRESS (LOW BYTE) XTAL1 PAGEL/BS1 OE DATA ADDR0 (Low Byte) XA0 XA1/BS2 Note: The timing requirements shown in Table 19-9. Symbol ...
Page 192
Table 19-9. Symbol t BVDV t OLDV t OHDZ Notes: ATtiny261A/461A/861A 192 Parallel Programming Characteristics, V Parameter BS1 Valid to DATA valid OE Low to DATA Valid OE High to DATA Tri-stated valid for the Write Flash, ...
Page 193
Typical Characteristics The data contained in this section is largely based on simulations and characterization of similar devices in the same process and design methods. Thus, the data should be treated as indica- tions of how the part will ...
Page 194
Table 20-2. PRR bit PRTIM1 PRTIM0 PRUSI PRADC It is possible to calculate the typical current consumption based on the numbers from for other V 20.1.1 Example Calculate the expected current consumption in idle mode with TIMER0, ADC, and USI ...
Page 195
ATtiny261A 20.2.1 Current Consumption in Active Mode Figure 20-1. Active Supply Current vs. Low Frequency (0.1 - 1.0 MHz) 0.8 0.6 0.4 0.2 Figure 20-2. Active Supply Current vs. Frequency ( MHz) 8197B–AVR–01/10 ACTIVE SUPPLY CURRENT vs. ...
Page 196
Figure 20-3. Active Supply Current vs. V Figure 20-4. Active Supply Current vs. V ATtiny261A/461A/861A 196 CC ACTIVE SUPPLY CURRENT vs. SUPPLY VOLTAGE 1 ACTIVE SUPPLY CURRENT vs. SUPPLY VOLTAGE ...
Page 197
Figure 20-5. Active Supply Current vs. V 20.2.2 Current Consumption in Idle Mode Figure 20-6. Idle Supply Current vs. Low Frequency (0.1 - 1.0 MHz) 8197B–AVR–01/10 ACTIVE SUPPLY CURRENT vs. SUPPLY VOLTAGE 0.12 0.1 0.08 0.06 0.04 0.02 0 1.5 ...
Page 198
Figure 20-7. Idle Supply Current vs. Frequency ( MHz) Figure 20-8. Idle Supply Current vs. V ATtiny261A/461A/861A 198 IDLE SUPPLY CURRENT vs. FREQUENCY 3 2.5 2 1.5 1 0.5 1 Frequency ...
Page 199
Figure 20-9. Idle Supply Current vs. V Figure 20-10. Idle Supply Current vs. V 0.025 0.02 0.015 0.01 0.005 8197B–AVR–01/10 CC IDLE SUPPLY CURRENT vs. V INTERNAL OSCILLATOR, 1 MHz 0.35 0.3 0.25 0.2 0.15 0.1 0.05 0 1.5 2 ...
Page 200
Current Consumption in Power-Down Mode Figure 20-11. Power-down Supply Current vs. V Figure 20-12. Power-down Supply Current vs. V ATtiny261A/461A/861A 200 POWER-DOWN SUPPLY CURRENT vs. SUPPLY VOLTAGE 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 1.5 2 2.5 3 ...