PIC18F25J11-I/SS Microchip Technology, PIC18F25J11-I/SS Datasheet - Page 26
![IC PIC MCU FLASH 32K 2V 28-SSOP](/photos/6/81/68119/150-28-ssop_sml.jpg)
PIC18F25J11-I/SS
Manufacturer Part Number
PIC18F25J11-I/SS
Description
IC PIC MCU FLASH 32K 2V 28-SSOP
Manufacturer
Microchip Technology
Series
PIC® XLP™ 18Fr
Datasheets
1.MA180023.pdf
(528 pages)
2.PIC18LF24J10-ISS.pdf
(32 pages)
3.PIC18F24J11-ISS.pdf
(14 pages)
Specifications of PIC18F25J11-I/SS
Core Size
8-Bit
Program Memory Size
32KB (16K x 16)
Core Processor
PIC
Speed
48MHz
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
16
Program Memory Type
FLASH
Ram Size
3.8K x 8
Voltage - Supply (vcc/vdd)
2.15 V ~ 3.6 V
Data Converters
A/D 10x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
28-SSOP
Controller Family/series
PIC18
No. Of I/o's
16
Ram Memory Size
3.6875KB
Cpu Speed
48MHz
No. Of Timers
5
Interface
EUSART, I2C, SPI
Processor Series
PIC18F
Core
PIC
Data Bus Width
8 bit
Data Ram Size
3776 B
Interface Type
EUSART, I2C, SPI
Maximum Clock Frequency
48 MHz
Number Of Timers
5
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
Development Tools By Supplier
PG164130, DV164035, DV244005, DV164005, PG164120, DM183022, DM183032, DV164136, MA180023
Minimum Operating Temperature
- 40 C
On-chip Adc
10 bit, 10 Channel
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
AC164322 - MODULE SOCKET MPLAB PM3 28/44QFN
Eeprom Size
-
Lead Free Status / Rohs Status
Details
PIC18F2XJXX/4XJXX FAMILY
TABLE 5-7:
DS39687E-page 26
RTCOSC
DSWDTOSC
MSSPMSK
PLLSEL
ADCSEL
IOL1WAY
WPCFG
WPFP<6:0>
WPEND
WPDIS
LS48MHZ
DEV<2:0>
REV<4:0>
DEV<10:3>
Note 1: The Configuration bits can only be programmed indirectly by programming the Flash Configuration Word.
Bit Name
(5)
2: The Configuration bits are reset to ‘1’ only on V
3: These bits are not implemented in PIC18F47J13 family devices.
4: Once this bit is cleared, all the Configuration registers which reside in the last page are also protected. To disable code
5: Not implemented on PIC18F47J53 family devices.
(3)
(1,2)
protection, perform an ICSP™ Bulk Erase operation.
PIC18F47J13 AND PIC18F47J53 FAMILY DEVICES: BIT DESCRIPTIONS (CONTINUED)
Configuration
CONFIG3H
CONFIG3H
CONFIG3H
CONFIG3H
CONFIG4H
CONFIG4H
CONFIG4H
CONFIG3L
CONFIG3L
CONFIG4L
CONFIG4L
DEVID1
DEVID1
DEVID2
Words
RTCC Reference Clock Select bit
1 = RTCC uses T1OSC/T1CKI as reference clock
0 = RTCC uses INTRC as reference clock
DSWDT Reference Clock Select bit
1 = DSWDT uses INTRC as reference clock
0 = DSWDT uses T1OSC/T1CKI as reference clock
MSSP 7-Bit Address Masking Mode Enable bit
1 = 7-Bit Address Masking mode enable
0 = 5-Bit Address Masking mode enable
PLL Selection bit
1 = 4x PLL selected
0 = 96 MHz PLL selected
ADC Mode Selection bit
1 = 10-Bit ADC mode selected
0 = 12-Bit ADC mode selected
IOLOCK Bit One-Way Set Enable bit
1 = The IOLOCK bit (PPSCON<0>) can be set once, provided the unlock sequence has
0 = The IOLOCK bit (PPSCON<0>) can be set and cleared as needed, provided the
Write/Erase Protect Configuration Words Page bit (valid when WPDIS = 0)
1 = Configuration Words page is not erase/write-protected unless WPEND and
0 = Configuration Words page is erase/write-protected, regardless of WPEND and
Write/Erase Protect Page Start/End Location bits
Used with WPEND bit to define which pages in Flash will be write/erase-protected.
Write/Erase Protect Region Select bit (valid when WPDIS = 0)
1 = Flash pages, WPFP<6:0> to Configuration Words page, are write/erase-protected
0 = Flash pages, 0 to WPFP<6:0> are write/erase-protected
Write Protect Disable bit
1 = WPFP<6:0>, WPEND and WPCFG bits ignored; all Flash memory may be erased or
0 = WPFP<6:0>, WPEND and WPCFG bits enabled; write/erase-protect active for the
System Clock Selection bit
1 = System clock is expected at 48 MHz, FS/LS USB CLKEN’s divide-by is set to 8
0 = System clock is expected at 24 MHz, FS/LS USB CLKEN’s divide-by is set to 4
Device ID bits
Used with the DEV<10:3> bits in the Device ID Register 2 to identify the part number.
Revision ID bits
Indicate the device revision.
Device ID bits
Used with the DEV<2:0> bits in the Device ID Register 1 to identify the part number.
been completed. Once set, the Peripheral Pin Select registers cannot be written to a
second time.
unlock sequence has been completed
WPFP<6:0> settings include the Configuration Words page
WPFP<6:0>
written
selected region(s)
DD
Reset; it is reloaded with the programmed value at any device Reset.
Description
© 2009 Microchip Technology Inc.