PIC18F25J11-I/SS Microchip Technology, PIC18F25J11-I/SS Datasheet - Page 126

• Manufacturer Part Number: PIC18F25J11-I/SS
• Description: IC PIC MCU FLASH 32K 2V 28-SSOP
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F25J11-I/SS

• Core Size: 8-Bit
• Program Memory Size: 32KB (16K x 16)
• Core Processor: PIC
• Speed: 48MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 16
• Program Memory Type: FLASH
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2.15 V ~ 3.6 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SSOP
• Controller Family/series: PIC18
• No. Of I/o's: 16
• Ram Memory Size: 3.6875KB
• Cpu Speed: 48MHz
• No. Of Timers: 5
• Interface: EUSART, I2C, SPI
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3776 B
• Interface Type: EUSART, I2C, SPI
• Maximum Clock Frequency: 48 MHz
• Number Of Timers: 5
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DM183022, DM183032, DV164136, MA180023
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 10 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC164322 - MODULE SOCKET MPLAB PM3 28/44QFN
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

PIC18F46J11 FAMILY
9.1.3
Though the V
these devices are still capable of interfacing with 5V
systems, even if the V
3.6V. This is accomplished by adding a pull-up resistor
to the port pin (Figure 9-2), clearing the LAT bit for that
pin and manipulating the corresponding TRIS bit
(Figure 9-1) to either allow the line to be pulled high or
to drive the pin low. Only port pins that are tolerant of
voltages up to 5.5V can be used for this type of
interface (refer to Section 9.1.2 “Input Pins and
Voltage Considerations”).
FIGURE 9-2:
EXAMPLE 9-1:
9.1.4
The output pins for several peripherals are also
equipped with a configurable open-drain output option.
This allows the peripherals to communicate with
external digital logic operating at a higher voltage level,
without the use of level translators.
DS39932C-page 126
BCF
BCF
BCF
PIC18F46J11
LATD, 7
TRISD, 7 ; send a 0 to the 5V system
TRISD, 7 ; send a 1 to the 5V system
INTERFACING TO A 5V SYSTEM
OPEN-DRAIN OUTPUTS
RD7
DDMAX
; set up LAT register so
; changing TRIS bit will
; drive line low
of the PIC18F46J11 family is 3.6V,
IH
+5V SYSTEM HARDWARE
INTERFACE
COMMUNICATING WITH
THE +5V SYSTEM
of the target system is above
+5V
+5V Device
The open-drain option is implemented on port pins
specifically associated with the data and clock outputs
of the EUSARTs, the MSSP modules (in SPI mode) and
the ECCP modules. It is selectively enabled by setting
the open-drain control bit for the corresponding module
in the ODCON registers (Register 9-1, Register 9-2
and Register 9-3). Their configuration is discussed in
more detail with the individual port where these
peripherals are multiplexed.
When the open-drain option is required, the output pin
must also be tied through an external pull-up resistor
provided by the user to a higher voltage level, up to
5.5V (Figure 9-3). When a digital logic high signal is
output, it is pulled up to the higher voltage level.
FIGURE 9-3:
9.1.5
Many of the digital I/O ports use Schmitt Trigger (ST)
input buffers. While this form of buffering works well
with many types of input, some applications may
require TTL level signals to interface with external logic
devices. This is particularly true for the Parallel Master
Port (PMP), which is likely to be interfaced to TTL level
logic or memory devices.
The inputs for the PMP can be optionally configured for
TTL buffers with the PMPTTL bit in the PADCFG1 reg-
ister (Register 9-4). Setting this bit configures all data
and control input pins for the PMP to use TTL buffers.
By default, these PMP inputs use the port’s ST buffers.
3.3V
TTL INPUT BUFFER OPTION
V
DD
PIC18F46J11
(at logic ‘1’)
USING THE OPEN-DRAIN
OUTPUT (USART SHOWN
AS EXAMPLE)
© 2009 Microchip Technology Inc.
TX
X
+5V
5V