PIC24HJ64GP510-E/PF Microchip Technology, PIC24HJ64GP510-E/PF Datasheet - Page 223

• Manufacturer Part Number: PIC24HJ64GP510-E/PF
• Description: IC PIC MCU FLASH 32KX16 100TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 24Hr

Specifications of PIC24HJ64GP510-E/PF

• Core Processor: PIC
• Core Size: 16-Bit
• Speed: 40 MIPs
• Connectivity: CAN, I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 85
• Program Memory Size: 64KB (22K x 24)
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 32x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 100-TQFP, 100-VQFP
• For Use With: DM300024 - KIT DEMO DSPICDEM 1.1MA240012 - MODULE PLUG-IN PIC24H 100QFPDV164033 - KIT START EXPLORER 16 MPLAB ICD2DM240001 - BOARD DEMO PIC24/DSPIC33/PIC32AC164323 - MODULE SKT FOR 100TQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

22.0
The PIC24H instruction set is identical to that of the
PIC24F, and is a subset of the dsPIC30F/33F
instruction set.
Most instructions are a single program memory word
(24 bits). Only three instructions require two program
memory locations.
Each single-word instruction is a 24-bit word, divided
into an 8-bit opcode, which specifies the instruction
type and one or more operands, which further specify
the operation of the instruction.
The instruction set is highly orthogonal and is grouped
into five basic categories:
• Word or byte-oriented operations
• Bit-oriented operations
• Literal operations
• DSP operations
• Control operations
Table 22-1 shows the general symbols used in
describing the instructions.
The PIC24H instruction set summary in Table 22-2 lists
all the instructions, along with the status flags affected
by each instruction.
Most word or byte-oriented W register instructions
(including
operands:
• The first source operand which is typically a
• The second source operand which is typically a
• The destination of the result which is typically a
© 2009 Microchip Technology Inc.
Note:
register ‘Wb’ without any address modifier
register ‘Ws’ with or without an address modifier
register ‘Wd’ with or without an address modifier
INSTRUCTION SET SUMMARY
This data sheet summarizes the features
of
families of devices. However, it is not
intended to be a comprehensive reference
source. To complement the information in
this data sheet, refer to the related section
in the “PIC24H Family Reference Manual”,
which is available from the Microchip
website (www.microchip.com).
barrel
the
shift
PIC24HJXXXGPX06/X08/X10
instructions)
have
PIC24HJXXXGPX06/X08/X10
three
However, word or byte-oriented file register instructions
have two operands:
• The file register specified by the value ‘f’
• The destination, which could either be the file
Most bit-oriented instructions (including simple
rotate/shift instructions) have two operands:
• The W register (with or without an address
• The bit in the W register or file register
The literal instructions that involve data movement may
use some of the following operands:
• A literal value to be loaded into a W register or file
• The W register or file register where the literal
However, literal instructions that involve arithmetic or
logical operations use some of the following operands:
• The first source operand which is a register ‘Wb’
• The second source operand which is a literal
• The destination of the result (only if not the same
The control instructions may use some of the following
operands:
• A program memory address
• The mode of the table read and table write
register ‘f’ or the W0 register, which is denoted as
‘WREG’
modifier) or file register (specified by the value of
‘Ws’ or ‘f’)
(specified by a literal value or indirectly by the
contents of register ‘Wb’)
register (specified by the value of ‘k’)
value is to be loaded (specified by ‘Wb’ or ‘f’)
without any address modifier
value
as the first source operand) which is typically a
register ‘Wd’ with or without an address modifier
instructions
DS70175H-page 221