PIC24HJ64GP510-E/PF Microchip Technology, PIC24HJ64GP510-E/PF Datasheet - Page 11
![IC PIC MCU FLASH 32KX16 100TQFP](/photos/12/13/121330/c04-100-tqfp_sml.jpg)
PIC24HJ64GP510-E/PF
Manufacturer Part Number
PIC24HJ64GP510-E/PF
Description
IC PIC MCU FLASH 32KX16 100TQFP
Manufacturer
Microchip Technology
Series
PIC® 24Hr
Datasheets
1.PIC24HJ12GP201-ISO.pdf
(84 pages)
2.PIC24HJ64GP206-IPT.pdf
(292 pages)
3.PIC24HJ64GP206-IPT.pdf
(8 pages)
4.PIC24HJ64GP206-IPT.pdf
(20 pages)
5.PIC24HJ64GP206-IPT.pdf
(26 pages)
Specifications of PIC24HJ64GP510-E/PF
Core Processor
PIC
Core Size
16-Bit
Speed
40 MIPs
Connectivity
CAN, I²C, IrDA, LIN, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, DMA, POR, PWM, WDT
Number Of I /o
85
Program Memory Size
64KB (22K x 24)
Program Memory Type
FLASH
Ram Size
8K x 8
Voltage - Supply (vcc/vdd)
3 V ~ 3.6 V
Data Converters
A/D 32x10b/12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 125°C
Package / Case
100-TQFP, 100-VQFP
For Use With
DM300024 - KIT DEMO DSPICDEM 1.1MA240012 - MODULE PLUG-IN PIC24H 100QFPDV164033 - KIT START EXPLORER 16 MPLAB ICD2DM240001 - BOARD DEMO PIC24/DSPIC33/PIC32AC164323 - MODULE SKT FOR 100TQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
FIGURE 3-4:
© 2010 Microchip Technology Inc.
BaseAddress + 0x80
BaseAddress =
No
RemainingCmds = 1368
RemainingCmds =
RemainingCmds – 1
BaseAddress = 0x0
Command to Program
FLOWCHART FOR
PROGRAMMING CODE
MEMORY
RemainingCmds
BaseAddress
PROGP response
Send PROGP
PASS?
Start
‘0’?
End
Is
Is
Yes
Yes
Report Error
No
Failure
3.5.2
After code memory is programmed, the contents of
memory can be verified to ensure that programming
was successful. Verification requires code memory to
be read back and compared against the copy held in
the programmer’s buffer.
The READP command can be used to read back all the
programmed code memory.
Alternatively, you can have the programmer perform
the verification after the entire device is programmed,
using a checksum computation.
3.5.3
Only the Configuration registers are included in the
checksum computation. The Device ID and Unit ID are
not included in the checksum computation.
TABLE D-1: “CHECKSUM COMPUTATION”
how this 16-bit computation can be made for each
dsPIC33F and PIC24H device. Computations for read
code protection are shown both enabled and disabled.
The checksum values shown here assume that the
Configuration registers are also erased. However,
when code protection is enabled, the value of the FGS
register is assumed to be 0x5.
PROGRAMMING VERIFICATION
CHECKSUM COMPUTATION
DS70152H-page 11
shows