PIC18F452-E/P Microchip Technology, PIC18F452-E/P Datasheet - Page 4
![IC MCU CMOS 40MHZ 16K FLSH 40DIP](/photos/6/61/66192/150-40-dip_sml.jpg)
PIC18F452-E/P
Manufacturer Part Number
PIC18F452-E/P
Description
IC MCU CMOS 40MHZ 16K FLSH 40DIP
Manufacturer
Microchip Technology
Series
PIC® 18Fr
Datasheets
1.PIC16F616T-ISL.pdf
(8 pages)
2.PIC18F242-ISO.pdf
(332 pages)
3.PIC18F242-ISO.pdf
(14 pages)
4.PIC18F242-ISO.pdf
(16 pages)
5.PIC18F242-ISO.pdf
(16 pages)
6.PIC18F242-ISO.pdf
(14 pages)
7.PIC18LF242-ISO.pdf
(36 pages)
8.PIC18F452-EP.pdf
(332 pages)
Specifications of PIC18F452-E/P
Program Memory Type
FLASH
Program Memory Size
32KB (16K x 16)
Package / Case
40-DIP (0.600", 15.24mm)
Core Processor
PIC
Core Size
8-Bit
Speed
40MHz
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, LVD, POR, PWM, WDT
Number Of I /o
34
Eeprom Size
256 x 8
Ram Size
1.5K x 8
Voltage - Supply (vcc/vdd)
4.2 V ~ 5.5 V
Data Converters
A/D 8x10b
Oscillator Type
External
Operating Temperature
-40°C ~ 125°C
Processor Series
PIC18F
Core
PIC
Data Bus Width
8 bit
Data Ram Size
1.5 KB
Interface Type
MSSP/SPI/I2C/PSP/USART
Maximum Clock Frequency
40 MHz
Number Of Programmable I/os
34
Number Of Timers
4
Operating Supply Voltage
2 V to 5.5 V
Maximum Operating Temperature
+ 125 C
Mounting Style
Through Hole
3rd Party Development Tools
52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
Development Tools By Supplier
PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DV164136, DM163022
Minimum Operating Temperature
- 40 C
On-chip Adc
8-ch x 10-bit
Package
40PDIP
Device Core
PIC
Family Name
PIC18
Maximum Speed
40 MHz
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
ACICE0206 - ADAPTER MPLABICE 40P 600 MIL
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC18F452-E/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
PIC18FXX2
8. Module: Data EEPROM
9. Module: MSSP (All I
DS80122K-page 4
When reading the data EEPROM, the contents of
the EEDATA register may be corrupted if the RD
bit (EECON1<0>) is set immediately following a
write to the address byte (EEADR). The actual
contents of the data EEPROM remain unaffected.
Work around
Do not set EEADR immediately before the
execution of a read. Write to EEADR at least one
instruction cycle before setting the RD bit. The
instruction between the write to EEADR and the
read can be any valid instruction, including a NOP.
Date Codes that pertain to this issue:
All engineering and production devices.
The Buffer Full (BF) flag bit of the SSPSTAT
register (SSPSTAT<0>) may be inadvertently
cleared even when the SSPBUF register has not
been read. This will occur only when the following
two conditions occur simultaneously:
• The four Least Significant bits of the BSR register
• Any instruction that contains C9h in its 8 Least
Work around
All work arounds will involve setting the contents of
BSR<3:0> to some value other than 0Fh.
In addition to those proposed below, other
solutions may exist.
1. When developing or modifying code, keep
2. If accessing a part of Bank 15 is required and
3. If pointing the BSR to Bank 15 is unavoidable,
Date Codes that pertain to this issue:
All engineering and production devices.
are equal to 0Fh (BSR<3:0> = 1111) and
Significant bits (i.e., register file addresses,
literal data, address offsets, etc.) is executed.
these guidelines in mind:
• Assign 12-bit addresses to all variables.
• Do not set the BSR to point to Bank 15
• Allow the assembler to manipulate the
the use of Access Banking is not possible,
consider using indirect addressing.
review the absolute file listing. Verify that no
instructions contain C9h in the 8 Least
Significant bits while the BSR points to Bank 15
(BSR = 0Fh).
This allows the assembler to know when
Access Banking can be used.
(BSR = 0Fh).
access bit present in most instructions.
Accessing the SFRs in Bank 15 will be done
through the Access Bank. Continue to use
the BSR to select all GPR Banks.
2
C™ and SPI™ Modes)
10. Module: MSSP (SPI, Slave Mode)
11. Module: Core (Instruction Set)
EXAMPLE 2:
MOVLW
ADDLW
BTFSC
INCFSZ byte2
DAW
BTFSC
INCFSZ byte2
This is repeated for each DAW instruction.
In its current implementation, the SS (Slave
Select) control signal, generated by an external
master processor, may not be successfully recog-
nized by the PIC
Slave Select mode (SSPM3:SSPM0 = 0100). In
particular, it has been observed that faster
transitions (those with shorter fall times) are more
likely to be missed than than slower transitions.
Work around
Insert a series resistor between the source of the
SS signal and the corresponding SS input line of
the microcontroller. The value of the resistor is
dependent on both the application system’s
characteristics and process variations between
microcontrollers. Experimentation and thorough
testing is encouraged.
This is a recommended solution. Others may exist.
Date Codes that pertain to this issue:
All engineering and production devices.
The Decimal Adjust W register instruction, DAW,
may improperly clear the Carry bit (STATUS<0>)
when executed.
Work around
Test the Carry bit state before executing the DAW
instruction. If the Carry bit is set, increment the
next higher byte to be added using an instruction
such as INCFSZ (this instruction does not affect
any Status flags, and will not overflow a BCD
nibble). After the DAW instruction has been
executed, process the Carry bit normally (see
Example 2).
0x80
0x80
STATUS,C
STATUS,C
PROCESSING THE CARRY
BIT DURING BCD ADDITIONS
®
; .80 (BCD)
; .80 (BCD)
; test C
; inc next higher LSB
; test C
; inc next higher LSB
© 2005 Microchip Technology Inc.
microcontroller operating in