PIC24FJ256GA110-I/PT Microchip Technology, PIC24FJ256GA110-I/PT Datasheet - Page 157

• Manufacturer Part Number: PIC24FJ256GA110-I/PT
• Description: IC PIC MCU FLASH 256K 100TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 24Fr

Specifications of PIC24FJ256GA110-I/PT

• Program Memory Type: FLASH
• Program Memory Size: 256KB (85.5K x 24)
• Package / Case: 100-TFQFP
• Core Processor: PIC
• Core Size: 16-Bit
• Speed: 32MHz
• Connectivity: I²C, PMP, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 85
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC24FJ
• Core: PIC
• Data Bus Width: 16 bit
• Data Ram Size: 16 KB
• Interface Type: I2C/SPI/UART
• Maximum Clock Frequency: 32 MHz
• Number Of Programmable I/os: 85
• Number Of Timers: 5
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52713-733, 52714-737, 53276-922, EWDSPIC
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DM240001, DM240011
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 16-ch x 10-bit
• Package: 100TQFP
• Device Core: PIC
• Family Name: PIC24
• Maximum Speed: 32 MHz
• Operating Supply Voltage: 2.5|3.3 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 876-1004 - PIC24 BREAKOUT BOARDMA240015 - BOARD MCV PIM FOR 24F256GADM240011 - KIT STARTER MPLAB FOR PIC24F MCUAC164333 - MODULE SKT FOR PM3 100QFP
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

For 32-bit cascaded operation, these steps are also
necessary:
1.
2.
3.
4.
5.
6.
Depending on the output mode selected, the module
holds the OCx pin in its default state, and forces a tran-
sition to the opposite state when OCxR matches the
timer. In Double Compare modes, OCx is forced back
to its default state when a match with OCxRS occurs.
The OCxIF interrupt flag is set after an OCxR match in
Single Compare modes, and after each OCxRS match
in Double Compare modes.
Single-shot pulse events only occur once, but may be
repeated by simply rewriting the value of the
OCxCON1 register. Continuos pulse events continue
indefinitely until terminated.
© 2008 Microchip Technology Inc.
Set
(OCyCON2<8> and (OCxCON2<8>). Enable
the even-numbered module first to ensure the
modules will start functioning in unison.
Clear the OCTRIG bit of the even module
(OCyCON2), so the module will run in
Synchronous mode.
Configure the desired output and Fault settings
for OCyCON2.
Force the output pin for OCx to the output state
by clearing the OCTRIS bit.
If Trigger mode operation is required, configure
the trigger options in OCx by using the OCTRIG
(OCxCON2<7>), TRIGSTAT (OCxCON2<6>)
and SYNCSEL (OCxCON2<4:0>) bits.
Configure the desired Compare or PWM mode
of operation (OCM<2:0>) for OCyCON1 first,
then for OCxCON1.
the
OC32
bits
for
both
registers
PIC24FJ256GA110 FAMILY
Preliminary
13.3
In PWM mode, the enhanced output compare module
can be configured for edge-aligned or center-aligned
pulse waveform generation. All PWM operations are
double-buffered (buffer registers are internal to the
module and are not mapped into SFR space).
To set up the module for PWM operations:
1.
2.
3.
4.
5.
6.
7.
8.
Note:
Configure the OCx output for one of the
available Peripheral Pin Select pins.
Calculate the desired duty cycles and load them
into the OCxR register.
Calculate the desired period and load it into the
OCxRS register.
Select the current OCx as the trigger/sync
source by writing 0x1F to SYNCSEL<4:0>
(OCxCON2<4:0>).
Select
OCTSEL2<2:0> (OCxCON<12:10>) bits.
Enable interrupts, if required, for the timer and
output compare modules. The output compare
interrupt is required for PWM Fault pin utilization.
Select the desired PWM mode in the OCM<2:0>
(OCxCON1<2:0>) bits.
If a timer is selected as a clock source, set the
TMRy prescale value and enable the time base
by setting the TON (TxCON<15>) bit.
Pulse-Width Modulation (PWM)
Mode
This peripheral contains input and output
functions that may need to be configured
by the Peripheral Pin Select. See
Section 9.4 “Peripheral Pin Select” for
more information.
a
clock
source
by
DS39905B-page 155
writing
the