ATSAM3U2EA-AU Atmel, ATSAM3U2EA-AU Datasheet - Page 19
![IC MCU 32BIT 128KB FLASH 144LQFP](/photos/6/72/67244/144l1-lqfp_sml.jpg)
ATSAM3U2EA-AU
Manufacturer Part Number
ATSAM3U2EA-AU
Description
IC MCU 32BIT 128KB FLASH 144LQFP
Manufacturer
Atmel
Series
SAM3Ur
Specifications of ATSAM3U2EA-AU
Core Processor
ARM® Cortex-M3™
Core Size
32-Bit
Speed
96MHz
Connectivity
EBI/EMI, I²C, MMC, SPI, SSC, UART/USART, USB
Peripherals
Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
Number Of I /o
96
Program Memory Size
128KB (128K x 8)
Program Memory Type
FLASH
Ram Size
36K x 8
Voltage - Supply (vcc/vdd)
1.65 V ~ 1.95 V
Data Converters
A/D 8x10b, 8x12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
144-LQFP
Controller Family/series
SAM3U
No. Of I/o's
96
Ram Memory Size
36KB
Cpu Speed
96MHz
No. Of Timers
3
Rohs Compliant
Yes
Processor Series
ATSAM3x
Core
ARM Cortex M3
Data Bus Width
32 bit
Data Ram Size
36 KB
Interface Type
4xUSART, 2xTWI, 5xSPI, Bus
Maximum Clock Frequency
96 MHz
Number Of Programmable I/os
96
Number Of Timers
8
Operating Supply Voltage
1.62 V to 3.6 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
JTRACE-CM3, MDK-ARM, RL-ARM, ULINK2
Development Tools By Supplier
ATSAM3U-EK
Minimum Operating Temperature
- 40 C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Lead Free Status / Rohs Status
Details
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
5.4
5.5
5.5.1
5.5.2
6430CS–ATARM–09-Apr-10
Active Mode
Low Power Modes
Backup Mode
Wait Mode
Active mode is the normal running mode with the core clock running from the fast RC oscillator,
the main crystal oscillator or the PLLA. The power management controller can be used to adapt
the frequency and to disable the peripheral clocks.
The various low power modes of the SAM3U are described below:
The purpose of backup mode is to achieve the lowest power consumption possible in a system
which is performing periodic wake-ups to perform tasks but not requiring fast startup time
(<0.5ms).
The Supply Controller, zero-power power-on reset, RTT, RTC, Backup registers and 32 kHz
Oscillator (RC or crystal oscillator selected by software in the Supply Controller) are running.
The regulator and the core supply are off.
Backup Mode is based on the Cortex-M3 deep-sleep mode with the voltage regulator disabled.
The SAM3U Series can be awakened from this mode through the Force Wake-Up pin (FWUP),
and Wake-Up input pins WKUP0 to WKUP15, Supply Monitor, RTT or RTC wake-up event. Cur-
rent Consumption is 2.5 µA typical on VDDBU.
Backup mode is entered by using WFE instructions with the SLEEPDEEP bit in the System Con-
trol Register of the Cortex-M3 set to 1. (See the “Power Management” description in The “ARM
Cortex M3 Processor” section of the product datasheet).
Exit from Backup mode happens if one of the following enable wake up events occurs:
The purpose of the wait mode is to achieve very low power consumption while maintaining the
whole device in a powered state for a startup time of less than 10 µs.
In this mode, the clocks of the core, peripherals and memories are stopped. However, the core,
peripherals and memories power supplies are still powered. From this mode, a fast start up is
available.
This mode is entered via Wait for Event (WFE) instructions with LPM = 1 (Low Power Mode bit in
PMC_FSMR). The Cortex-M3 is able to handle external events or internal events in order to
wake-up the core (WFE). By configuring the external lines WKUP0-15 as fast startup wake-up
pins (refer to
used to wake up the CPU (exit from WFE).
Current Consumption in Wait mode is typically 15 µA on VDDIN if the internal voltage regulator
is used or 8 µA on VDDCORE if an external regulator is used.
• FWUP pin (low level, configurable debouncing)
• WKUPEN0-15 pins (level transition, configurable debouncing)
• SM alarm
• RTC alarm
• RTT alarm
Section 5.7 “Fast
Start-Up”). RTC or RTT Alarm and USB wake-up events can be
SAM3U Series
19