W78E052DPG Nuvoton Technology Corporation of America, W78E052DPG Datasheet - Page 58
![no-image](/images/manufacturer_photos/0/4/485/nuvoton_technology_corporation_of_america_sml.jpg)
W78E052DPG
Manufacturer Part Number
W78E052DPG
Description
IC MCU 8-BIT 8K FLASH 44-PLCC
Manufacturer
Nuvoton Technology Corporation of America
Series
W78r
Datasheet
1.W78E051DPG.pdf
(89 pages)
Specifications of W78E052DPG
Core Processor
8052
Core Size
8-Bit
Speed
40MHz
Connectivity
EBI/EMI, UART/USART
Peripherals
POR, WDT
Number Of I /o
36
Program Memory Size
8KB (8K x 8)
Program Memory Type
FLASH
Ram Size
256 x 8
Voltage - Supply (vcc/vdd)
2.4 V ~ 5.5 V
Oscillator Type
External
Operating Temperature
-40°C ~ 85°C
Package / Case
44-PLCC
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Data Converters
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
W78E052DPG
Manufacturer:
Nuvoton Technology Corporation of America
Quantity:
10 000
Part Number:
W78E052DPG
Manufacturer:
NUVOTON
Quantity:
20 000
W78E054D/W78E052D/W78E051D Data Sheet
Figure 16- 1 Serial port mode 0
The TI flag is set high in S6P2 following the end of transmission of the last bit. The serial port will re-
ceive data when REN is 1 and RI is zero. The shift clock (TxD) will be activated and the serial port will
latch data on the rising edge of shift clock. The external device should therefore present data on the
falling edge on the shift clock. This process continues till all the 8 bits have been received. The RI flag
is set in S6P2 following the last rising edge of the shift clock on TxD. This will stop reception, till the RI
is cleared by software.
16.2 MODE 1
In Mode 1, the full duplex asynchronous mode is used. Serial communication frames are made up of
10 bits transmitted on TXD and received on RXD. The 10 bits consist of a start bit (0), 8 data bits (LSB
first), and a stop bit (1). On receive, the stop bit goes into RB8 in the SFR SCON. The baud rate in this
mode is variable. The serial baud can be programmed to be 1/16 or 1/32 of the Timer 1 overflow.
Since the Timer 1 can be set to different reload values, a wide variation in baud rates is possible.
Transmission begins with a write to SBUF. The serial data is brought out on to TxD pin at S6P2 follow-
ing the first roll-over of divide by 16 counter. The next bit is placed on TxD pin at S6P2 following the
next rollover of the divide by 16 counter. Thus the transmission is synchronized to the divide by 16
counter and not directly to the write to SBUF signal. After all 8 bits of data are transmitted, the stop bit
is transmitted. The TI flag is set in the S6P2 state after the stop bit has been put out on TxD pin. This
will be at the 10th rollover of the divide by 16 counters after a write to SBUF.
Reception is enabled only if REN is high. The serial port actually starts the receiving of serial data,
with the detection of a falling edge on the RxD pin. The 1-to-0 detector continuously monitors the RxD
line, sampling it at the rate of 16 times the selected baud rate. When a falling edge is detected, the
divide by 16 counters is immediately reset. This helps to align the bit boundaries with the rollovers of
the divide by 16 counters.
- 58 -