MC908QB4MDWE Freescale Semiconductor, MC908QB4MDWE Datasheet - Page 170

• Manufacturer Part Number: MC908QB4MDWE
• Description: IC MCU 8BIT 4K FLASH 16-SOIC
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908QB4MDWE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 13
• Program Memory Size: 4KB (4K x 8)
• Program Memory Type: FLASH
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 16-SOIC (0.300", 7.5mm Width)
• Processor Series: HC08QB
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: 3-Wire, ESCI, SPI, UART
• Number Of Programmable I/os: 13
• Number Of Timers: 4
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, M68CBL05AE, DEMO908QB8, DEMO908QC16
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 10 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Serial Peripheral Interface (SPI) Module
When an SPI is configured as a slave, the SS pin is always configured as an input. It cannot be used as
a general-purpose I/O regardless of the state of the MODFEN control bit. However, the MODFEN bit can
still prevent the state of SS from creating a MODF error. See
When an SPI is configured as a master, the SS input can be used in conjunction with the MODF flag to
prevent multiple masters from driving MOSI and SPSCK. (See
of the SS pin to set the MODF flag, the MODFEN bit in the SPSCK register must be set. If the MODFEN
bit is 0 for an SPI master, the SS pin can be used as a general-purpose I/O under the control of the data
direction register of the shared I/O port. When MODFEN is 1, it is an input-only pin to the SPI regardless
of the state of the data direction register of the shared I/O port.
User software can read the state of the SS pin by configuring the appropriate pin as an input and reading
the port data register. See
15.8 Registers
The following registers allow the user to control and monitor SPI operation:
170
•
•
•
SPI control register (SPCR)
SPI status and control register (SPSCR)
SPI data register (SPDR)
1. X = Don’t care
SPE
0
1
1
1
A high on the SS pin of a slave SPI puts the MISO pin in a high-impedance
state. The slave SPI ignores all incoming SPSCK clocks, even if it was
already in the middle of a transmission.
MASTER SS
MISO/MOSI
SLAVE SS
SLAVE SS
CPHA = 0
CPHA = 1
SPMSTR
X
0
1
1
(1)
Table 15-2.
MODFEN
BYTE 1
Figure 15-12. CPHA/SS Timing
Table 15-2. SPI Configuration
MC68HC908QB8 Data Sheet, Rev. 3
X
X
0
1
Master without MODF
SPI Configuration
Master with MODF
NOTE
Not enabled
Slave
BYTE 2
15.8.2 SPI Status and Control Register.
15.3.6.2 Mode Fault
General-purpose I/O;
General-purpose I/O;
Function of SS Pin
SS ignored by SPI
SS ignored by SPI
BYTE 3
Input-only to SPI
Input-only to SPI
Freescale Semiconductor
Error.) For the state