S9S08AW16AE0CFT Freescale Semiconductor, S9S08AW16AE0CFT Datasheet - Page 298

• Manufacturer Part Number: S9S08AW16AE0CFT
• Description: MCU 16K FLASH AUTO 48-QFN
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of S9S08AW16AE0CFT

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SCI, SPI
• Peripherals: LVD. POR, PWM, WDT
• Number Of I /o: 38
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-QFN Exposed Pad
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

1
2
3
4
5
6
7
8
9
Appendix A Electrical Characteristics and Timing Specifications
298
Num
Typical values are based on characterization data at V
Self-clocked mode frequency is the frequency that the DCO generates when the FLL is open-loop.
Loss of reference frequency is the reference frequency detected internally, which transitions the ICG into self-clocked mode if it
is not in the desired range.
Loss of DCO frequency is the DCO frequency detected internally, which transitions the ICG into FLL bypassed external mode
(if an external reference exists) if it is not in the desired range.
This parameter is characterized before qualification rather than 100% tested.
Proper PC board layout procedures must be followed to achieve specifications.
This specification applies to the period of time required for the FLL to lock after entering FLL engaged internal or external modes.
If a crystal/resonator is being used as the reference, this specification assumes it is already running.
Jitter is the average deviation from the programmed frequency measured over the specified interval at maximum f
Measurements are made with the device powered by filtered supplies and clocked by a stable external clock signal. Noise
injected into the FLL circuitry via V
a given interval.
See
19
Figure
MC9S08AWxx: Internal oscillator deviation from trimmed frequency
S9S08AWxx: Internal oscillator deviation from trimmed frequency
C
C
C
P
P
P
A-9.
(V
V
V
V
V
V
DDA
DD
DD
DD
DD
DD
= 2.7 – 5.5 V, (constant temperature)
= 5.0 V ±10%, –40° C to 125°C
= 2.7 – 5.5 V, (constant temperature)
= 5.0 V ±10%, –40° C to 85°C
= 5.0 V ±10%, –40° C to 125°C
= V
DDA
Table A-12. ICG Frequency Specifications (continued)
(min) to V
Characteristic
DDA
and V
DDA
SSA
MC9S08AW60 Data Sheet, Rev 2
(max), Temperature Range = –40 to 125°C Ambient)
and variation in crystal oscillator frequency increase the C
DD
= 5.0V, 25°C unless otherwise stated.
Symbol
ACC
ACC
9
9
int
int
Min
—
—
—
—
—
Typ
±0.5
±0.5
±0.5
±0.5
±0.5
Freescale Semiconductor
1
Jitter
Max
±1.5
±1.5
±2
±2
±2
percentage for
ICGOUT
Unit
.
%
%
%
%
%