S9S08DZ32F1MLF Freescale Semiconductor, S9S08DZ32F1MLF Datasheet - Page 267

• Manufacturer Part Number: S9S08DZ32F1MLF
• Description: MCU 32K FLASH MASK AUTO 48-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of S9S08DZ32F1MLF

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: CAN, I²C, LIN, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 39
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 16x12b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 48-LQFP
• Processor Series: S08D
• Core: HCS08
• Data Bus Width: 8 bit
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: DEMO9S08DZ60
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

12.5.5.5
In initialization mode, any on-going transmission or reception is immediately aborted and synchronization
to the CAN bus is lost, potentially causing CAN protocol violations. To protect the CAN bus system from
fatal consequences of violations, the MSCAN immediately drives the TXCAN pin into a recessive state.
In initialization mode, the MSCAN is stopped. However, interface registers remain accessible. This mode
is used to reset the CANCTL0, CANRFLG, CANRIER, CANTFLG, CANTIER, CANTARQ,
CANTAAK, and CANTBSEL registers to their default values. In addition, the MSCAN enables the
configuration of the CANBTR0, CANBTR1 bit timing registers; CANIDAC; and the CANIDAR,
CANIDMR message filters. See
description of the initialization mode.
Due to independent clock domains within the MSCAN, INITRQ must be synchronized to all domains by
using a special handshake mechanism. This handshake causes additional synchronization delay (see
Section Figure 12-46., “Initialization Request/Acknowledge
If there is no message transfer ongoing on the CAN bus, the minimum delay will be two additional bus
clocks and three additional CAN clocks. When all parts of the MSCAN are in initialization mode, the
INITAK flag is set. The application software must use INITAK as a handshake indication for the request
(INITRQ) to go into initialization mode.
Freescale Semiconductor
MSCAN Initialization Mode
The user is responsible for ensuring that the MSCAN is not active when
initialization mode is entered. The recommended procedure is to bring the
MSCAN into sleep mode (SLPRQ = 1 and SLPAK = 1) before setting the
INITRQ bit in the CANCTL0 register. Otherwise, the abort of an on-going
message can cause an error condition and can impact other CAN bus
devices.
The CPU cannot clear INITRQ before initialization mode (INITRQ = 1 and
INITAK = 1) is active.
Bus Clock Domain
CPU
Init Request
INITAK
Flag
Figure 12-46. Initialization Request/Acknowledge Cycle
Section 12.3.1, “MSCAN Control Register 0
MC9S08DZ60 Series Data Sheet, Rev. 4
INITRQ
sync.
INITAK
NOTE
NOTE
SYNC
SYNC
Chapter 12 Freescale’s Controller Area Network (S08MSCANV1)
Cycle”).
CAN Clock Domain
sync.
INITRQ
INITAK
(CANCTL0),” for a detailed
INIT
Flag
267