MC908GR16AVFAER Freescale Semiconductor, MC908GR16AVFAER Datasheet - Page 246

• Manufacturer Part Number: MC908GR16AVFAER
• Description: IC MCU 8BIT 16K FLASH 48-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908GR16AVFAER

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: LIN, SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 37
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 48-LQFP
• Controller Family/series: HC08
• No. Of I/o's: 37
• Ram Memory Size: 1KB
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: SCI, SPI
• Rohs Compliant: Yes
• Processor Series: HC08GR
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: ESCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 37
• Number Of Timers: 4
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, DEMO908GZ60E, M68CBL05CE, M68EML08GPGTE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Development Support
19.3.2 Security
A security feature discourages unauthorized reading of FLASH locations while in monitor mode. The host
can bypass the security feature at monitor mode entry by sending eight security bytes that match the
bytes at locations $FFF6–$FFFD. Locations $FFF6–$FFFD contain user-defined data.
During monitor mode entry, the MCU waits after the power-on reset for the host to send the eight security
bytes on pin PTA0. If the received bytes match those at locations $FFF6–$FFFD, the host bypasses the
security feature and can read all FLASH locations and execute code from FLASH. Security remains
bypassed until a power-on reset occurs. If the reset was not a power-on reset, security remains bypassed
and security code entry is not required. See
Upon power-on reset, if the received bytes of the security code do not match the data at locations
$FFF6–$FFFD, the host fails to bypass the security feature. The MCU remains in monitor mode, but
reading a FLASH location returns an invalid value and trying to execute code from FLASH causes an
illegal address reset. After receiving the eight security bytes from the host, the MCU transmits a break
character, signifying that it is ready to receive a command.
To determine whether the security code entered is correct, check to see if bit 6 of RAM address $40 is
set. If it is, then the correct security code has been entered and FLASH can be accessed.
If the security sequence fails, the device should be reset by a power-on reset and brought up in monitor
mode to attempt another entry. After failing the security sequence, the FLASH module can also be mass
erased by executing an erase routine that was downloaded into internal RAM. The mass erase operation
clears the security code locations so that all eight security bytes become $FF (blank).
246
Notes:
1 = Echo delay, approximately 2 bit times
2 = Data return delay, approximately 2 bit times
4 = Wait 1 bit time before sending next byte
5 = Wait until the monitor ROM runs
Do not leave locations $FFF6–$FFFD blank. For security reasons, program
locations $FFF6–$FFFD even if they are not used for vectors.
The MCU does not transmit a break character until after the host sends the
eight security bytes.
V
RST
PA0
DD
Figure 19-17. Monitor Mode Entry Timing
FROM HOST
MC68HC908GR16A Data Sheet, Rev. 1.0
4096 + 32 CGMXCLK CYCLES
FROM MCU
5
Figure
NOTE
NOTE
1
19-17.
4
1
1
2
Freescale Semiconductor
4
1