C8051F047-GQ Silicon Laboratories Inc, C8051F047-GQ Datasheet - Page 278

• Manufacturer Part Number: C8051F047-GQ
• Description: IC 8051 MCU 32K FLASH 64TQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F04xr

Specifications of C8051F047-GQ

• Program Memory Type: FLASH
• Program Memory Size: 32KB (32K x 8)
• Package / Case: 64-TQFP, 64-VQFP
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: CAN, EBI/EMI, SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 32
• Ram Size: 4.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 13x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F0x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 4.25 KB
• Interface Type: CAN/SMBus/SPI/UART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 5
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F040DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 13-ch x 10-bit
• No. Of I/o's: 32
• Ram Memory Size: 4352Byte
• Cpu Speed: 25MHz
• No. Of Timers: 5
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1212

C8051F040/1/2/3/4/5/6/7
22.1. Enhanced Baud Rate Generation
The UART1 baud rate is generated by Timer 1 in 8-bit auto-reload mode. The TX clock is generated by
TL1; the RX clock is generated by a copy of TL1 (shown as RX Timer in Figure 22.2), which is not user-
accessible. Both TX and RX Timer overflows are divided by two to generate the TX and RX baud rates.
The RX Timer runs when Timer 1 is enabled, and uses the same reload value (TH1). However, an
RX Timer reload is forced when a START condition is detected on the RX pin. This allows a receive to
begin any time a START is detected, independent of the TX Timer state.
Timer 1 should be configured for Mode 2, 8-bit auto-reload (see
Timer with Auto-Reload” on page
occur at two times the desired baud rate. Note that Timer 1 may be clocked by one of five sources: SYS-
CLK, SYSCLK / 4, SYSCLK / 12, SYSCLK / 48, or the external oscillator clock / 8. For any given Timer 1
clock source, the UART1 baud rate is determined by Equation 22.1, where T1
clock supplied to Timer 1, and TH1 is the high byte of Timer 1 (reload value).

Timer 1 clock frequency is selected as described in
quick reference for typical baud rates and system clock frequencies is given in Table 22.1 through
Table 22.6. Note that the internal oscillator may still generate the system clock when the external oscillator
is driving Timer 1 (see
278
Detected
Start
Section “23.1. Timer 0 and Timer 1” on page 287
Figure 22.2. UART1 Baud Rate Logic
RX Timer
Equation 22.1. UART1 Baud Rate
UartBaudRate
Timer 1
TH1
TL1
289). The Timer 1 reload value should be set so that overflows will
Overflow
Overflow
Rev. 1.5
=
Section “23.1. Timer 0 and Timer 1” on page
------------------------------ -

256 TH1
T1
–
CLK
Section “23.1.3. Mode 2: 8-bit Counter/
2
2

UART1

1
-- -
2
for more details).
RX Clock
TX Clock
CLK
is the frequency of the
287. A