C8051F041-GQR Silicon Laboratories Inc, C8051F041-GQR Datasheet - Page 113

• Manufacturer Part Number: C8051F041-GQR
• Description: IC 8051 MCU 64K FLASH 64TQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F04xr

Specifications of C8051F041-GQR

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: CAN, EBI/EMI, SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 32
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 4.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 8x8b, 13x12b; D/A 2x10b, 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TQFP, 64-VQFP
• For Use With: 336-1205 - DEV KIT FOR F040/F041/F042/F043
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

9.
The voltage reference circuit offers full flexibility in operating the ADC and DAC modules. Three voltage ref-
erence input pins allow each ADC and the two DACs (C8051F040/2 only) to reference an external voltage
reference or the on-chip voltage reference output. ADC0 may also reference the DAC0 output internally,
and ADC2 may reference the analog power supply voltage, via the VREF multiplexers shown in Figure 9.1.
The internal voltage reference circuit consists of a 1.2 V, temperature stable bandgap voltage reference
generator and a gain-of-two output buffer amplifier. The internal reference may be routed via the VREF pin
to external system components or to the voltage reference input pins shown in Figure 9.1. Bypass capaci-
tors of 0.1 µF and 4.7 µF are recommended from the VREF pin to AGND, as shown in Figure 9.1. See
Table 9.1 for voltage reference specifications.
The Reference Control Register, REF0CN (defined in SFR Definition 9.1) enables/disables the internal ref-
erence generator and selects the reference inputs for ADC0 and ADC2. The BIASE bit in REF0CN enables
the on-board reference generator while the REFBE bit enables the gain-of-two buffer amplifier which drives
the VREF pin. When disabled, the supply current drawn by the bandgap and buffer amplifier falls to less
than 1 µA (typical) and the output of the buffer amplifier enters a high impedance state. If the internal band-
gap is used as the reference voltage generator, BIASE and REFBE must both be set to logic 1. If the inter-
nal reference is not used, REFBE may be set to logic 0. Note that the BIASE bit must be set to logic 1 if
either DAC or ADC is used, regardless of the voltage reference used. If neither the ADC nor the DAC are
being used, both of these bits can be set to logic 0 to conserve power. Bits AD0VRS and AD2VRS select
the ADC0 and ADC2 voltage reference sources, respectively. The electrical specifications for the Voltage
Reference are given in Table 9.1.
The temperature sensor connects to the highest order input of the ADC0 input multiplexer (see
“5.1. Analog Multiplexer and PGA” on page 47
plexer and PGA” on page 69
disables the temperature sensor. While disabled, the temperature sensor defaults to a high impedance
state and any A/D measurements performed on the sensor while disabled result in meaningless data.
Voltage Reference (C8051F040/2/4/6)
Figure 9.1. Voltage Reference Functional Block Diagram
Reference
External
Voltage
Circuit
VDD
Recommended Bypass
4.7F
R1
for C8051F042/4/6 devices). The TEMPE bit within REF0CN enables and
Capacitors
0.1F
(C8051F040/2 only)
VREF2
VREF0
VREFD
VREF
Rev. 1.5
for C8051F040 devices, or
REF0CN
C8051F040/1/2/3/4/5/6/7
DAC0
DAC1
Ref
REFBE
x2
AV+
(C8051F040/2 only)
1
0
0
1
Band-Gap
BIASE
1.2V
EN
ADC2
Ref
ADC0
Ref
Section “6.1. Analog Multi-
Bias to
ADCs,
DACs
Section
113