SC5554MVR132 Freescale Semiconductor, SC5554MVR132 Datasheet - Page 50

• Manufacturer Part Number: SC5554MVR132
• Description: MCU MPC5554 DP ONLY 416-PBGA
• Manufacturer: Freescale Semiconductor
• Series: MPC55xx Qorivvar

Specifications of SC5554MVR132

• Core Processor: e200z6
• Core Size: 32-Bit
• Speed: 132MHz
• Connectivity: CAN, EBI/EMI, SCI, SPI
• Peripherals: DMA, POR, PWM, WDT
• Number Of I /o: 256
• Program Memory Size: 2MB (2M x 8)
• Program Memory Type: FLASH
• Ram Size: 64K x 8
• Voltage - Supply (vcc/vdd): 1.35 V ~ 1.65 V
• Data Converters: A/D 40x12b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 416-PBGA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

Revision History for the MPC5554 Data Sheet
5
The history of revisions made to this data sheet are described in this section.
5.1
The substantive changes incorporated in MPC5554 Data Sheet Rev. 2.0 to produce Rev. 3.0 are listed in
Table
50
Throughout:
Title page:
Section 1, “Overview”
Section 3.2.1, “General Notes for Specifications at Maximum Junction Temperature
Section 3.7, “Power-Up/Down Sequencing
Section 3.7.3, “Power-Down Sequence (VRC33
Section 4.1, “MPC5554 416 PBGA Pinout”
Location
28. The changes are listed in sequential page number order.
Revision History for the MPC5554 Data Sheet
Changes to Revision 2 in Revision 3
Changed ‘T
Changed the Revision number from 2 to 3. Changed theh date. Made the same change in the lower left corner of
the back page.
Updated the address of Semiconductor Equipment and Materials International
3081 Zanker Rd.
San Jose, CA., 95134
[phone]
Last paragraph: Changed the first sentence FROM , , , the voltage on the pins goes to high-impedance until . . .
TO. . .the pins go to a high-impedance state until . . .
Last sentence: Changed from: ‘This ensures that the digital 1.5 V logic, which is reset by the ORed POR only and
can cause the 1.5 V supply to decrease below its specification, is reset properly.’
To: ‘This ensures that the digital 1.5 V logic, which is reset only by an ORed POR and can cause the 1.5 V supply
to decrease less than its specification, resets correctly.’
Added the following NOTE before the 416 BGA Map:
• Fourth paragraph, First sentence: Deleted ‘of the MPC5500 family’; Second to last sentence: Deleted ‘can’.
• Fifth paragraph, First sentence: Replaced ‘MPC5500 family’ with ‘MPC5554’; Last sentence: Replaced ‘can be’
• Sixth paragraph, First sentence: Replaced ‘MPC5500 family’ with ‘MPC5554’;
• Second to last paragraph: Rewrote to read: The MCU has an on-chip enhanced queued dual analog-to-digital
with ‘is’.
converter (eQADC). The 416 package has 40-channels.
The MPC5500 devices are pin compatible for software portability and use the primary
function names to label the pins in the BGA diagram. Although some devices do not support
all the primary functions shown in the BGA diagram, the muxed and GPIO signals on those
pins remain available. See the signals chapter in the device reference manual for the signal
muxing.
A
= T
L
– T
H
’ to ‘T
Table 28. Changes Between Rev. 2.0 and 3.0
MPC5554 Microcontroller Data Sheet, Rev. 3.0
A
= T
L
to T
Grounded)”
H
.’
Description of Changes
NOTE
Freescale Semiconductor