DS80C323-QCD Maxim Integrated Products, DS80C323-QCD Datasheet - Page 22

• Manufacturer Part Number: DS80C323-QCD
• Description: IC MCU HI SPEED 18MHZ 44-PLCC
• Manufacturer: Maxim Integrated Products
• Series: 80Cr

Specifications of DS80C323-QCD

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 18MHz
• Connectivity: EBI/EMI, SIO, UART/USART
• Peripherals: Power-Fail Reset, WDT
• Number Of I /o: 32
• Program Memory Type: ROMless
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Oscillator Type: External
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 44-LCC, 44-PLCC
• Processor Series: DS80C323
• Core: 8051
• Data Bus Width: 8 bit
• Program Memory Size: 64 KB
• Data Ram Size: 64 KB
• Interface Type: UART
• Maximum Clock Frequency: 18 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 3
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Minimum Operating Temperature: 0 C
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Program Memory Size: -
• Data Converters: -

NOTES FOR DS80C320 DC ELECTRICAL CHARACTERISTICS
All parameters apply to both commercial and industrial temperature operation unless otherwise noted. Specifications to -40°C
are guaranteed by design and are not production tested.
1. All voltages are referenced to ground.
2. Active current is measured with a 25MHz clock source driving XTAL1, V
3. Idle mode current is measured with a 25MHz clock source driving XTAL1, V
4.
5. When addressing external memory. This specification only applies to the first clock cycle following transition.
6. RST = V
7. During a 0-to-1 transition, a one-shot drives the ports hard for two clock cycles. This measurement reflects port
8. Ports 1 and 3 source transition current when being pulled down externally. It reaches its maximum at
9. 0.45<V
10. Over the industrial temperature range, this specification has a maximum value of 200A.
11. This is the current required from an external circuit to hold a logic low level on an I/O pin while the
12.
TYPICAL I
disconnected.
other pins disconnected.
Stop mode current measured with XTAL1 and RST grounded, V
in transition mode.
approximately 2V.
dedicated as an address bus on the DS80C320. Peak current occurs near the input transition point of the latch,
approximately 2V.
corresponding port latch bit is set to 1. This is only the current required to hold the low level; transitions from 1
to 0 on an I/O pin will also have to overcome the transition current.
Device operating range is 4.5V to 5.5V; however, device is tested to 4.0V to ensure proper operation at
minimum V
IN
CC
CC
<V
. This condition mimics operation of pins in I/O mode.
RST
CC
vs. FREQUENCY
. Not a high-impedance input. This port is a weak address holding latch because Port 0 is
.
DS80C320/DS80C323 High-Speed/Low-Power Microcontrollers
22 of 38
CC
= 5.5V, all other pins disconnected.
CC
CC
= RST = 5.5V, all other pins
= 5.5V, RST at ground, all