PIC16C716/JW Microchip Technology, PIC16C716/JW Datasheet - Page 27

• Manufacturer Part Number: PIC16C716/JW
• Description: IC MCU EPROM2KX14 A/D PWM 18CDIP
• Manufacturer: Microchip Technology
• Series: PIC® 16Cr

Specifications of PIC16C716/JW

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 13
• Program Memory Size: 3.5KB (2K x 14)
• Program Memory Type: EPROM, UV
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Data Converters: A/D 4x8b
• Oscillator Type: External
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 18-CDIP (0.300", 7.62mm) Window
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Connectivity: -
• Other names: PIC16C716/JWR; PIC16C716/JWR; Q811661

PORTB pins RB3:RB1 are multiplexed with several
peripheral functions (Table 3-3). PORTB pins RB3:RB0
have Schmitt Trigger input buffers.
When enabling peripheral functions, care should be
taken in defining TRIS bits for each PORTB pin. Some
peripherals override the TRIS bit to make a pin an out-
put, while other peripherals override the TRIS bit to
make a pin an input. Since the TRIS bit override is in
effect while the peripheral is enabled, read-modify-
write instructions (BSF, BCF, XORWF) with TRISB as
destination should be avoided. The user should refer to
the corresponding peripheral section for the correct
TRIS bit settings.
Four of PORTB’s pins, RB7:RB4, have an interrupt-on-
change feature. Only pins configured as inputs can
cause this interrupt to occur (i.e., any RB7:RB4 pin
configured as an output is excluded from the interrupt-
on-change comparison). The input pins, RB7:RB4, are
compared with the old value latched on the last read of
FIGURE 3-4:
© 2005 Microchip Technology Inc.
Note 1: To enable weak pull-ups, set the appropriate TRIS bit(s) and clear the RBPU bit (OPTION_REG<7>).
Data Bus
RD
DATACCP
WR
DATACCP
WR
TRISCCP
WR
PORTB
WR TRISB
T1OSCEN
TMR1CS
BLOCK DIAGRAM OF RB1/T1OSO/T1CKI PIN
TMR1CS
RD PORTB
TRISCCP<0>
DATACCP<0>
PORTB<1>
TRISB<1>
D
D
D
D
CK
CK
CK
CK
Q
Q
Q
Q
Q
Q
Q
Q
1
0
RBPU
T1OSCEN
T1CS
(1)
T1CLKIN
1
0
TTL Buffer
1
1
0
0
PORTB. The “mismatch” outputs of RB7:RB4 are
OR’ed together to generate the RB Port Change
Interrupt with flag bit RBIF (INTCON<0>).
This interrupt can wake the device from Sleep. The
user, in the Interrupt Service Routine, can clear the
interrupt in the following manner:
a)
b)
A mismatch condition will continue to set flag bit RBIF.
Reading PORTB will end the mismatch condition and
allow flag bit RBIF to be cleared.
The interrupt-on-change feature is recommended for
wake-up on key depression operation and operations
where PORTB is only used for the interrupt-on-change
feature. Polling of PORTB is not recommended while
using the interrupt-on-change feature.
Any read or write of PORTB will end the
mismatch condition.
Clear flag bit RBIF.
ST
Buffer
V
P
DD
Weak
Pull-up
PIC16C712/716
V
SS
V
DD
RB1/T1OSO/T1CKI
DS41106B-page 25