AT90S8535-8PC Atmel, AT90S8535-8PC Datasheet - Page 56
![IC MCU 8K FLSH 8MHZ A/D 40DIP](/photos/6/70/67049/453-40-dip_sml.jpg)
AT90S8535-8PC
Manufacturer Part Number
AT90S8535-8PC
Description
IC MCU 8K FLSH 8MHZ A/D 40DIP
Manufacturer
Atmel
Series
AVR® 90Sr
Specifications of AT90S8535-8PC
Core Processor
AVR
Core Size
8-Bit
Speed
8MHz
Connectivity
SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
32
Program Memory Size
8KB (4K x 16)
Program Memory Type
FLASH
Eeprom Size
512 x 8
Ram Size
512 x 8
Voltage - Supply (vcc/vdd)
4 V ~ 6 V
Data Converters
A/D 8x10b
Oscillator Type
Internal
Operating Temperature
0°C ~ 70°C
Package / Case
40-DIP (0.600", 15.24mm)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AT90S8535-8PC
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
SS Pin Functionality
Data Modes
56
AT90S/LS8535
When the SPI is configured as a master (MSTR in SPCR is set), the user can determine
the direction of the SS pin. If SS is configured as an output, the pin is a general output
pin, which does not affect the SPI system. If SS is configured as an input, it must be held
high to ensure master SPI operation. If the SS pin is driven low by peripheral circuitry
when the SPI is configured as master with the SS pin defined as an input, the SPI sys-
tem interprets this as another master selecting the SPI as a slave and starting to send
data to it. To avoid bus contention, the SPI system takes the following actions:
1. The MSTR bit in SPCR is cleared and the SPI system becomes a slave. As a
2. The SPIF flag in SPSR is set and if the SPI interrupt is enabled and the I-bit in
Thus, when interrupt-driven SPI transmission is used in Master Mode and there exists a
possibility that SS is driven low, the interrupt should always check that the MSTR bit is
still set. Once the MSTR bit has been cleared by a slave select, it must be set by the
user to re-enable the SPI Master Mode.
When the SPI is configured as a slave, the SS pin is always input. When SS is held low,
the SPI is activated and MISO becomes an output if configured so by the user. All other
pins are inputs. When SS is driven high, all pins are inputs and the SPI is passive, which
means that it will not receive incoming data. Note that the SPI logic will be reset once
the SS pin is brought high. If the SS pin is brought high during a transmission, the SPI
will stop sending and receiving immediately and both data received and data sent must
be considered as lost.
There are four combinations of SCK phase and polarity with respect to serial data,
which are determined by control bits CPHA and CPOL. The SPI data transfer formats
are shown in Figure 39 and Figure 40.
Figure 39. SPI Transfer Format with CPHA = 0 and DORD = 0
result of the SPI becoming a slave, the MOSI and SCK pins become inputs.
SREG are set, the interrupt routine will be executed.
(FOR REFERENCE)
(FROM MASTER)
SS (TO SLAVE)
(FROM SLAVE)
SCK (CPOL=0)
SCK (CPOL=1)
SCK CYCLE#
SAMPLE
MOSI
MISO
*Not defined but normally MSB of character just received.
MSB
MSB
1
2
6
6
3
5
5
4
4
4
5
3
3
6
2
2
7
1
1
LSB
LSB
8
*
1041H–11/01