PIC16LC774-I/P Microchip Technology, PIC16LC774-I/P Datasheet - Page 107
![IC MCU OTP 4KX14 A/D PWM 40DIP](/photos/6/61/66192/150-40-dip_sml.jpg)
PIC16LC774-I/P
Manufacturer Part Number
PIC16LC774-I/P
Description
IC MCU OTP 4KX14 A/D PWM 40DIP
Manufacturer
Microchip Technology
Series
PIC® 16Cr
Specifications of PIC16LC774-I/P
Core Processor
PIC
Core Size
8-Bit
Speed
20MHz
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
33
Program Memory Size
7KB (4K x 14)
Program Memory Type
OTP
Ram Size
256 x 8
Voltage - Supply (vcc/vdd)
2.5 V ~ 5.5 V
Data Converters
A/D 10x12b
Oscillator Type
External
Operating Temperature
-40°C ~ 85°C
Package / Case
40-DIP (0.600", 15.24mm)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC16LC774-I/PQ
Manufacturer:
Microchip Technology
Quantity:
10 000
Company:
Part Number:
PIC16LC774-I/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
9.3
In Synchronous Master mode, the data is transmitted in
a half-duplex manner i.e. transmission and reception
do not occur at the same time. When transmitting data,
the reception is inhibited and vice versa. Synchronous
mode is entered by setting bit SYNC (TXSTA<4>). In
addition enable bit SPEN (RCSTA<7>) is set in order to
configure the RC6/TX/CK and RC7/RX/DT I/O pins to
CK (clock) and DT (data) lines respectively. The Master
mode indicates that the processor transmits the master
clock on the CK line. The Master mode is entered by
setting bit CSRC (TXSTA<7>).
9.3.1
The USART transmitter block diagram is shown in
Figure
(serial) shift register (TSR). The shift register obtains its
data from the read/write transmit buffer register
TXREG. The TXREG register is loaded with data in
software. The TSR register is not loaded until the last
bit has been transmitted from the previous load. As
soon as the last bit is transmitted, the TSR is loaded
with new data from the TXREG (if available). Once the
TXREG register transfers the data to the TSR register
(occurs in one Tcycle), the TXREG is empty and inter-
rupt bit, TXIF (PIR1<4>) is set. The interrupt can be
TABLE 9-8
Address Name
0Ch
18h
19h
8Ch
98h
99h
Legend: x = unknown, - = unimplemented, read as '0'. Shaded cells are not used for Synchronous Master Transmission.
Note 1: Bits PSPIE and PSPIF are reserved on the 28-pin devices, always maintain these bits clear.
1999 Microchip Technology Inc.
9-3. The heart of the transmitter is the transmit
USART Synchronous Master Mode
USART SYNCHRONOUS MASTER
TRANSMISSION
TXREG USART Transmit Register
SPBRG Baud Rate Generator Register
PIR1
RCSTA
PIE1
TXSTA
REGISTERS ASSOCIATED WITH SYNCHRONOUS MASTER TRANSMISSION
PSPIF
PSPIE
SPEN
CSRC
Bit 7
(1)
(1)
ADIF
ADIE
Bit 6
RX9
TX9
SREN CREN ADDEN
TXEN SYNC
RCIF
RCIE
Bit 5
Bit 4
TXIF
TXIE
Advance Information
SSPIE
SSPIF
Bit 3
—
CCP1IE TMR2IE TMR1IE
CCP1IF TMR2IF TMR1IF
BRGH
FERR
Bit 2
enabled/disabled by setting/clearing enable bit TXIE
(PIE1<4>). Flag bit TXIF will be set regardless of the
state of enable bit TXIE and cannot be cleared in soft-
ware. It will reset only when new data is loaded into the
TXREG register. While flag bit TXIF indicates the status
of the TXREG register, another bit TRMT (TXSTA<1>)
shows the status of the TSR register. TRMT is a read
only bit which is set when the TSR is empty. No inter-
rupt logic is tied to this bit, so the user has to poll this
bit in order to determine if the TSR register is empty.
The TSR is not mapped in data memory so it is not
available to the user.
Steps to follow when setting up a Synchronous Master
Transmission:
1.
2.
3.
4.
5.
6.
7.
Initialize the SPBRG register for the appropriate
baud rate
Enable the synchronous master serial port by
setting bits SYNC, SPEN, and CSRC.
If interrupts are desired, then set enable bit
TXIE.
If 9-bit transmission is desired, then set bit TX9.
Enable the transmission by setting bit TXEN.
If 9-bit transmission is selected, the ninth bit
should be loaded in bit TX9D.
Start transmission by loading data to the
TXREG register.
OERR
TRMT
Bit 1
(Section
RX9D
TX9D
Bit 0
9.1).
PIC16C77X
0000 0000
0000 000x
0000 0000
0000 0000
0000 -010
0000 0000
Value on:
POR,
BOR
DS30275A-page 107
other Resets
Value on all
0000 0000
0000 000x
0000 0000
0000 0000
0000 -010
0000 0000