AT87F51-24JI Atmel, AT87F51-24JI Datasheet - Page 5

• Manufacturer Part Number: AT87F51-24JI
• Description: IC MICRO CTRL 24MHZ 44PLCC
• Manufacturer: Atmel
• Series: 87Fr

Specifications of AT87F51-24JI

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 24MHz
• Connectivity: UART/USART
• Number Of I /o: 32
• Program Memory Size: 4KB (4K x 8)
• Program Memory Type: OTP Quick FLASH
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 6 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-PLCC
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Data Converters: -
• Peripherals: -

Power Down Mode
In the power down mode the oscillator is stopped, and the
instruction that invokes power down is the last instruction
executed. The on-chip RAM and Special Function Regis-
ters retain their values until the power down mode is termi-
nated. The only exit from power down is a hardware reset.
Reset redefines the SFRs but does not change the on-chip
RAM. The reset should not be activated before V
restored to its normal operating level and must be held
active long enough to allow the oscillator to restart and sta-
bilize.
Lock Bit Protection Modes
Programming the QuickFlash
The AT87F51 is shipped with the on-chip QuickFlash mem-
ory array ready to be programmed. The programming inter-
face needs a high-voltage (12-volt) program enable signal
and is compatible with conventional third-party Flash or
EPROM programmers.
The AT87F51 code memory array is programmed byte-by-
byte.
Programming Algorithm: Before programming the
AT87F51, the address, data, and control signals should be
set up according to the QuickFlash programming mode
table and Figures 3 and 4. To program the AT87F51, take
the following steps:
1. Input the desired memory location on the address
2. Input the appropriate data byte on the data lines.
3. Activate the correct combination of control signals.
4. Raise EA/V
5. Pulse ALE/PROG once to program a byte in the Quick-
1
2
3
4
lines.
Flash array or the lock bits. The byte-write cycle is self-
timed and typically takes no more than 1.5 ms. Repeat
steps 1 through 5, changing the address and data for
the entire array or until the end of the object file is
reached.
Program Lock Bits
LB1
U
P
P
P
PP
to 12V.
LB2
U
U
P
P
LB3
U
U
U
P
Protection Type
No program lock features.
MOVC instructions executed from external program memory are disabled from fetching code
bytes from internal memory, EA is sampled and latched on reset, and further programming of the
QuickFlash is disabled.
Same as mode 2, also verify is disabled.
Same as mode 3, also external execution is disabled.
CC
is
Program Memory Lock Bits
On the chip are three lock bits which can be left unpro-
grammed (U) or can be programmed (P) to obtain the addi-
tional features listed in the table below:
When lock bit 1 is programmed, the logic level at the EA pin
is sampled and latched during reset. If the device is pow-
ered up without a reset, the latch initializes to a random
value, and holds that value until reset is activated. It is nec-
essary that the latched value of EA be in agreement with
the current logic level at that pin in order for the device to
function properly.
Data Polling: The AT87F51 features Data Polling to indi-
cate the end of a write cycle. During a write cycle, an
attempted read of the last byte written will result in the com-
plement of the written datum on PO.7. Once the write cycle
has been completed, true data are valid on all outputs, and
the next cycle may begin. Data Polling may begin any time
after a write cycle has been initiated.
Ready/Busy: The progress of byte programming can also
be monitored by the RDY/BSY output signal. P3.4 is pulled
low after ALE goes high during programming to indicate
BUSY. P3.4 is pulled high again when programming is
done to indicate READY.
Program Verify: If lock bits LB1 and LB2 have not been
programmed, the programmed code data can be read back
via the address and data lines for verification. The lock bits
cannot be verified directly. Verification of the lock bits is
achieved by observing that their features are enabled.
Reading the Signature Bytes: The signature bytes are
read by the same procedure as a normal verification of
locations 030H, 031H, and 032H, except that P3.6 and
P3.7 must be pulled to a logic low. The values returned are
as follows.
(030H) = 1EH indicates manufactured by Atmel
(031H) = 87H indicates 87F family
(032H) = 01H indicates 87F51
5