PIC18C858-E/L Microchip Technology, PIC18C858-E/L Datasheet - Page 3

• Manufacturer Part Number: PIC18C858-E/L
• Description: IC MCU OTP 16KX16 CAN 84PLCC
• Manufacturer: Microchip Technology
• Series: PIC® 18Cr

Specifications of PIC18C858-E/L

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: CAN, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 68
• Program Memory Size: 32KB (16K x 16)
• Program Memory Type: OTP
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 16x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 84-PLCC
• For Use With: AC164310 - MODULE SKT FOR PM3 84PLCCDVA18XL840 - ADAPTER DEVICE ICE 84PLCCAC174012 - MODULE SKT PROMATEII 84PLCC
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Other names: PIC18C858E/L

8. Module: I/O (Parallel Slave Port)
9. Module: Interrupts
 2003 Microchip Technology Inc.
The Input Buffer Status bit of the PSPCON register
(PSPCON<7>) may be inadvertently cleared,
even when the PORTD input buffer has not been
read. This will occur only when the following two
conditions occur simultaneously:
•
•
Work around
All work arounds will involve setting the contents of
BSR<3:0> to some value other than 0Fh. In addition
to those proposed below, other solutions may exist.
1. When developing or modifying code, keep
2. If accessing a part of Bank 15 is required and
3. If pointing the BSR to Bank 15 is unavoidable,
High priority interrupts may become improperly
enabled, while low priority interrupts become
improperly disabled at the same time. This may
occur when low priority interrupts are in an
enabled state and the following conditions occur
simultaneously:
•
•
The four Least Significant bits of the
BSR register are equal to 0Fh
(BSR<3:0> = 1111), and
Any instruction that contains 83h in its
8 Least Significant bits (i.e., register file
addresses, literal data, address offsets,
etc.) is executed.
these guidelines in mind:
•
•
•
the use of Access Banking is not possible,
consider using indirect addressing.
review the absolute file listing. Verify that no
instructions contains 83h in the 8 Least Signif-
icant bits while the BSR points to Bank 15
(BSR = 0Fh).
High priority interrupts are being changed
from an enabled to a disabled state; and
One or more low priority interrupts occur.
Assign 12-bit addresses to all variables.
This allows the assembler to know when
Access Banking can be used.
Do not set the BSR to point to Bank 15
(BSR = 0Fh).
Allow the assembler to manipulate the
Access bit present in most instructions.
Accessing the SFRs in Bank 15 will be
done through the Access Bank. Con-
tinue to use the BSR to select Banks 1
through 5 and the upper half of Bank 0.
10. Module: I/O (PORTB
Work around
1. Always disable low priority interrupts before
2. Use the latest silicon revision when it becomes
The RB Port Change Flag bit of the INTCON reg-
ister (RBIF, INTCON<0>) may be inadvertently
cleared, even when the PORTB<7:4> pins have
not been read. This will occur only when the follow-
ing two conditions occur simultaneously:
•
•
Work around
All work arounds will involve setting the contents of
BSR<3:0> to some value other than 0Fh. In addition
to those proposed below, other solutions may exist.
1. When developing or modifying code, keep
2. If accessing a part of Bank 15 is required and
3. If pointing the BSR to Bank 15 is unavoidable,
disabling high priority interrupts. Re-enable
the low priority interrupts afterwards, if
necessary.
available.
The four Least Significant bits of the
BSR register are equal to 0Fh
(BSR<3:0> = 1111), and
Any instruction that contains 81h in its
8 Least Significant bits (i.e., register file
addresses, literal data, address offsets,
etc.) is executed.
these guidelines in mind:
•
•
•
the use of Access Banking is not possible,
consider using indirect addressing.
review the absolute file listing. Verify that no
instructions contain 81h in the 8 Least Signifi-
cant bits, while the BSR points to Bank 15
(BSR = 0Fh).
Assign 12-bit addresses to all variables.
This allows the assembler to know when
Access Banking can be used.
Do not set the BSR to point to Bank 15
(BSR = 0Fh).
Allow the assembler to manipulate the
Access bit present in most instructions.
Accessing the SFRs in Bank 15 will be
done through the Access Bank. Con-
tinue to use the BSR to select Banks 1
through 5, and the upper half of Bank 0.
PIC18C658/858
Interrupt-on-Change)
DS80126C-page 3