PIC18C252-E/SO Microchip Technology, PIC18C252-E/SO Datasheet - Page 120

• Manufacturer Part Number: PIC18C252-E/SO
• Description: IC MCU OTP 16KX16 A/D 28SOIC
• Manufacturer: Microchip Technology
• Series: PIC® 18Cr

Specifications of PIC18C252-E/SO

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 22
• Program Memory Size: 32KB (16K x 16)
• Program Memory Type: OTP
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 5x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 28-SOIC (7.5mm Width)
• Processor Series: PIC18C
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 1.5 KB
• Interface Type: MSSP, SPI, I2C, USART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 23
• Number Of Timers: 1 x 16 bit
• Operating Supply Voltage: 2.5 V to 5.5 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: ICE2000, DM163022, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 5 bit
• For Use With: I3DB18C452 - BOARD DAUGHTER ICEPIC3
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: PIC18C252E/SO

PIC18CXX2
REGISTER 14-2:
DS39026C-page 118
bit 7
bit 6
bit 5
SSPCON1: MSSP CONTROL REGISTER1
bit 7
WCOL: Write Collision Detect bit
Master mode:
1 = A write to the SSPBUF register was attempted while the I
0 = No collision
Slave mode:
1 = The SSPBUF register is written while it is still transmitting the previous word
0 = No collision
SSPOV: Receive Overflow Indicator bit
In SPI mode:
1 = A new byte is received while the SSPBUF register is still holding the previous data. In case
0 = No overflow
In I
1 = A byte is received while the SSPBUF register is still holding the previous byte. SSPOV is a
0 = No overflow
SSPEN: Synchronous Serial Port Enable bit
In both modes when enabled, these pins must be properly configured as input or output.
In SPI mode:
1 = Enables serial port and configures SCK, SDO, SDI, and SS as the source of the serial
0 = Disables serial port and configures these pins as I/O port pins
In I
1 = Enables the serial port and configures the SDA and SCL pins as the source of the
0 = Disables serial port and configures these pins as I/O port pins
Legend:
R = Readable bit
- n = Value at POR
WCOL
R/W-0
2
2
transmission to be started
(must be cleared in software)
of overflow, the data in SSPSR is lost. Overflow can only occur in Slave mode.
In Slave mode, the user must read the SSPBUF, even if only transmitting data to avoid
setting overflow.
In Master mode, the overflow bit is not set, since each new reception (and transmission) is
initiated by writing to the SSPBUF register (must be cleared in software).
“don’t care” in Transmit mode (must be cleared in software).
port pins
serial port pins
C mode:
C mode:
SSPOV
R/W-0
W = Writable bit
’1’ = Bit is set
SSPEN
R/W-0
R/W-0
CKP
U = Unimplemented bit, read as ‘0’
’0’ = Bit is cleared
SSPM3
R/W-0
2
SSPM2
C conditions were not valid for a
R/W-0
2001 Microchip Technology Inc.
x = Bit is unknown
SSPM1
R/W-0
SSPM0
R/W-0
bit 0